AT&T at&t partner plus communications system manual Doorphone Alert Extensions, Code #606

Page 54

Doorphone

Alert

Extensions

Code: #606

Description: Identifies the extension or extensions that ring when someone presses the button on a doorphone. Each doorphone can have up to five alert extensions. The doorphones can have five individual alert extensions or they can share alert extensions. Use procedures #604 and #605 (Doorphone 1 and Doorphone 2 Extensions) to assign doorphone extensions.

Valid Entries: 1 = Not an alert extension

2 = Doorphone 1 alert extension

3 = Doorphone 2 alert extension

4 = Both doors alert extension

Programming Steps:

1.Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 6 ] [ 0 ] [ 6 ]. The display reads:

DoorPhneAlert

Extension:

2.Enter the first alert extension. For example, to select extension 10, press [ 1 ] [ 0 ]. The display reads:

DoorPhneAlert 10

1 No Alert

3.To change the alert status, enter the appropriate setting as listed above. For example, to make this extension an alert for both doorphone exten- sions, press [ 4 ] . The display reads:

DoorPhneAlert 10

4 Doors 1 and 2

To select another alert extension, press [ Next Item ] or [ Prev Item ] until the extension number shows on the display. Repeat step 3.

IMPORTANT: If you press [ Next Proc ] , the system skips procedure #728, Sys- tem Reset—Programming Saved and returns to procedure #101, System Date.

To use procedure #728 at this point, you must enter [ # ] [ 7 ] [ 2 ] [ 8 ] .

= Factory Setting

To go to the next procedure: [ Next Proc ]

To go to a specific procedure: [ # ] [ x ] [ x ] [ x ]

 

 

 

To go to the previous procedure: [ Prev Proc ]

(where XXX is the procedure number)

 

 

 

To return data to the factory setting: [ Remove ]

To exit system programming: [Feature ] [ 0 ] [ 0 ]

 

 

 

 

 

 

 

System Programming 3-33

Image 54
Contents AT&T Copyright 1990 AT&T All Rights Reserved Issue October Contents Page How to Use This Guide Product Safety LabelsAbout This Guide How to Comment on This Guide Reference MaterialsSystem Components Specifications Control Unit Partner TeIephonesOther Equipment An Example System Setup Example System SetupSystem Components and Specifications Specifications Technical and Environmental Specifications Grounding to comply with Underwriters Laboratories ULInstalling the Hardware General Guidelines Installing the Control Unit Mount the Backplane on a WallInstalling the Hardware Installing Telephones and Other Equipment Press and hold # button for 5 secondsWall Mounting a Partner Telephone Removing a Module Replacing a ModuleSystem Programming Alphabetic List of Procedures Programming Methods Programming ExtensionProgramming Overlay Programming Overlay General Instructions Programming Procedures System DateSystem Day System Time Number of LinesCode #106 Transfer Return Rings PBX Dial-Out CodeCode #105 ConsiderationRecall Timer Duration Code #107Rotary Dialing Time out Outside Conference Code #108Code #109 Dial Mode Code #201Line Type Code #202Hold Disconnect Time Code #203Line Assignment Code #301Valid Entries 1 = Assigned Line Use Restriction Code #302Valid Entries 1 = Display Language Code #303Valid Entries 1 = English Automatic Privacy Code #304Abbreviated Ringing Code #305Copy Settings Outgoing Call Restrictions Code #401Code #403 Toll Call Prefix System PasswordCode #402 Valid Entries Any 4 digitsDisallowed Phone Number Lists Code #404Prevents all ca!ls to area code Disallowed List Assignment Code #405Emergency Phone Number List Code #406Allowed Phone Number Lists Code #407Code #408 Pickup Group Extensions Code #501Calling Group Extensions Code #502Night Service Button Code #503Programming Notes Night Service Group Code #504Fax Machine Extensions Code #601Music On Hold Code #602Valid Entries 1 = Active Hotline Code #603Doorphone 1 Extension Doorphone 2 Extension Code #605Code #604 Doorphone Alert Extensions Code #606System Reset Programming Saved System Speed Dial Numbers Code #728Press Feature 0 0 . The display reads Recall EnableFunction Button Display Description and Example Pause StopCentralized Telephone Programming Personal Speed Dial Numbers Overview Buttons and Labeling Sheets for Partner Phones Automatic Line Selection To exit Automatic Line Selection, press the star * twiceLine Ringing Options Valid Entries Immediate ringPersonal Speed Dial Numbers Auto Dial Numbers Feature Code Do Not DisturbExclusive Hold Save Number Redial RecallLast Number Redial Conference Drop Touch-Tone Enable PrivacyMessage Light On Message Light Off Call Pickup Pickup GroupLoudspeaker Paging Calling Group Programming for Operation Behind PBX or Centrex Programming Method aProgramming Method B No Outside Line Access Dialing Restrictions SummaryOutside Dialing Allowed Dialing Restrictions An Example Dial 1 201 Dial 1 800FCC Information Page Index Hotline #603, 3-31programming for, 2-1standard phone used as I i Wires, connecting, 2-2to 2-3Wiring specifications, 1-5,2-1 O g r a m m i n g Quick Reference System Programming Programming Quick Reference Issue 2, October