TOA Electronics CP-63 manual Block diagram for tielined exchanges

Page 7

B. Without personal number

3.Numbering schedule for stations and paging zones

A.With personal number (Standard)

Type of exchange

Single Exchange (EX-1) Exchange "A" (EX-2A/3A)

Exchange "B" (EX-2B/3B)

Exchange "C" (EX-3C)

	Numbering for stations			Numbering for	paging zones
Model		With	7 zones	Paging zone per exchange
	Without Paging	With	per
	Without Paging	paging	per	All call	Zone
		paging	exchange
			exchange
EX-610

EX-620

EX-610

EX-620

EX-610

EX-620

Numbering for stations

	Type of			Model
	exchange			Model	With
				Without paging	With
				Without paging	paging
					paging
	Single Exchange (EX-1)			EX-610
	Exchange	"A"	(EX-2A/3A)	EX-620
				EX-620
	Exchange	"B"	(EX-2B/3B)	EX-610
	Exchange	"B"	(EX-2B/3B)	EX-620
				EX-620
	Exchange	"C"	(EX-3C)	EX-610
	Exchange	"C"	(EX-3C)	EX-620
				EX-620
	Zone No. 16 through 22 and No. 31			through 37 are employed for Paging
	Numbering Schedule		of 45 zones with	3 exchanges established in the system

using the exchanges EX-610 and/or EX-620 and EX-630 (256 stations) connected by tie-line.

	Numbering for paging zones
7 zones	Paging zone per exchange
per	All call	Zone
exchange

4.Reduction of the number of stations and paging zones which results from the use of the Tie-line Interface Unit TI-62.

1.Mounting one (1) piece of the TI-62 decreases the number of the LM-62 (the 7th or the 15th LM-62) by one (1).

2.Unless the PI-62 is used, the system can have up to 8 more sta- tions by placing the LM-62 in the 8th or the 16th position.

<EX-610 >			<EX-620>
LM	Station No.		LM	Station No.	LM	Station No.	Note.
							Note.
1	200-207		1	200-207	9	264-271	LM: Line Modem Unit
							LM: Line Modem Unit
2	208-215		2	208-215	10	272-279	PI	: Paging Interface Unit
3	216-223		3	216-223	11	280-287	Tl	: Tie-line Interface Unit
3	216-223		3	216-223	11	280-287
4	224-231		4	224-231	12	288-295
5	232-239		5	232-239	13	296-303
6	240-247		6	240-247	14	304-311
7	248-255		7	248-255	15	312-319
8	256-263	PI	8	256-263	16	320-327		PI

5. Block diagram for tielined exchanges.

<EX-610 Tie-line>	<EX-620 Tie-line>
Exchange "A"
(EX-2A/3A)

Exchange "B" (EX-2B/3B)

Exchange "C" (EX-3C)

— 6—

Image 7

Contents CP-63 Contents Required Installation Hand Book Systems Introduction to the Installation Manual for EXES-6000Installation Hand Book of EXES-6000 Installation Hand Book of ExchangeFunctions Which Require Additional Units Example of Exchange Mounted on Intercom Cabinet Rack Function of the Central Processing Unit CP-63 TIE-LINE Connection of the ExchangesBlock diagram for tielined exchanges Relationship between the PI unit and the LM unit Wiring for TIE-LINE Connection of the Exchanges Example of connection of EX-620 exchange Example of connection of EX-620 exchange SW-C SW-B Function Select Switches SW-EFixed MINI-JUMPER JP2 Initial CP-63 SET UP Check of ROM & NMOS-RAM No calls on the system Trouble ShootingTie-line for 3 exchanges Reference for Connection Link Number between DL and Tl Link SW-A SW-B SW-C SW-D CP-63 DIP Switches for Function SelectionON/OFF Clearance at one time Function Code Table for Station no ProgrammingOFF Programming of SystemOperating for Programming Programming of each FunctionExecutive Priority Function Code 50 Highest Priority Station no Programming for Each FunctionYES Continuous Calling Tone Step Continuous Calling Tone Function CodeStations Allowed Access to ALL Call Step Stations Allowed Access to ALL Call Function CodeStations Allowed Access to Conference Step Stations Allowed Access to Conference Function CodeHandset Substations Allowed Access to Paging Step Automatic Access to Paging Function CodeCall by Dialing Picking up the Handset Complementary NotesStation Allowed Access to ONE Shot Make Output Step Stations Allowed Access to MAKE/BREAK Output Step Stations Allowed Access to MAKE/BREAK Output Function CodeTouch Function Code New Registration? Stations Allowed Access to 4 Decimal Digits Output Step Secretary Transfer Function Code MASTER/SUB Relationship MASTER/SUB Relationship Function CodeGroup Hunting Function Code Establishment of Each Paging Zone Paging Zone Function CodeEstablishment of Each Group Group BlockingRegistration of station numbers having indication panel Calling Party Indication Lamp Type Function CodeAllowing Calls Among Groups Group Blocking 2 Allowing Calls Among Groups Function CodeAllowing Access to Paging Zones Programming of Single Station Number Programmable Station Numbering Function CodeProgrammable Station Numbering Restriction of programmable station numbering Programming of Serial Station NumbersClearance of Each Function at a Time Programming Data TableInitial Programming Initial Programming of the ExchangeFunction Function Table for the SystemFunction Table for Stations Programming DataProgrammingdatatable For Tie-line Unit EX-620 Station Numbers Table for Calling Party Indication Lamp Type Individual Stations Channel Select Cable YR-802 or YR-806DIP Switch Table for Data Transmitting and Receiving Units YR-810 YR-802 Application Explanation of Data Transmitting Unit Output ChannelsChannel Selection Functions DescriptionChannel 0 CH In/Out Annunciation Explanation of Data Receiving Unit Output DataChannel Select Switch Channel 2 CH Calling Party Indication Lamp Type Channel Select SwitchChannel 3 CH Calling Party Indication Lamp Type Necessary module units KOBE, Japan