Polycom I640, H340, E340, 72-1065-09 manual Message Description Action

Page 41

 

SpectraLink Corporation

Configuration and Administration–NetLink e340/h340/ i640 Wireless Telephone

 

 

NetLink Telephony Gateway and SpectraLink Radio Protocol

 

 

 

 

 

 

Message

Description

Action

 

 

 

 

 

(battery icon),

Low battery.

In call: the battery icon displays and a soft

 

Battery Low,

 

beep will be heard when the user is on the

 

beep (audio)

 

handset and the battery charge is low. User

 

 

 

has 15–30 minutes of battery life left.

 

 

 

The Battery Pack can be changed while the

 

 

 

call is still in progress. Do not press Power

 

 

 

Off/End Call. Quickly remove the discharged

 

 

 

battery and replace with a charged battery,

 

 

 

power on the handset and press Power

 

 

 

On/Start Call to resume the call in progress.

 

 

 

Not in call: The battery icon displays whenever

 

 

 

the Battery Pack charge is low The message

 

 

 

Low Battery and a loud beep indicate a

 

 

 

critically low battery charge when user is not

 

 

 

on the handset. The handset will not work until

 

 

 

the Battery Pack is charged.

 

 

 

 

 

Battery Failure

The Battery Pack is not functioning.

Replace the Battery Pack with a new or

 

 

 

confirmed SpectraLink Battery pack. Any non-

 

 

 

SpectraLink Battery Packs will not work.

 

 

 

 

 

Battery Failed

Battery Pack is damaged or incompatible

Replace the Battery Pack with a new or

 

 

with handset.

confirmed SpectraLink Battery pack. Any non-

 

 

 

SpectraLink Battery Packs will not work.

 

 

 

 

 

Cant Renew DHCP

y…y = DHCP server IP address

Configuration problem. Check the IP address

 

yyy.yyy.yyy.yyy

DHCP server is not responding to initial

configuration in the DHCP server.

 

 

renewal attempt.

 

 

 

 

 

 

 

Charging …

The handset is charging in the Desktop

No action needed.

 

 

Charger.

 

 

 

 

 

 

 

Charge Complete

The handset is now fully charged

No action needed.

 

 

 

 

 

Checking Code

Handset is contacting the Download

None, this message should only last for

 

 

Master to determine if it has a newer

approximately one second. If message

 

 

version of software that should be

remains displayed, power off and contact

 

 

downloaded.

customer support for a replacement handset.

 

 

 

 

 

Checking DHCP IP

The handset is retrieving DHCP

None. This is informational only.

 

 

information from the DHCP server.

 

 

 

 

 

 

 

CRC Code Error

The software which has been TFTP

Try the download again, it is possible the

 

 

downloaded has a bad redundancy code

software was corrupted during download. If

 

 

check.

the error repeats, check that the download

 

 

 

image on the TFTP server is not corrupted.

 

 

 

 

 

Code Mismatch!

The software loaded into the handset is

Verify the License Management value is

 

 

incorrect for this model handset.

correct. Replace the software image on the

 

 

 

TFTP server with software that is correct for the

 

 

 

handset model.

 

 

 

 

 

DCA Timeout

The handset has detected a fault from

Turn the handset off then on again. If error

 

 

which it cannot recover, possibly due to a

persists, contact SpectraLink Technical

 

 

failure to acquire any network.

Support and report the error.

 

 

 

 

 

PN: 72-1065-09-J.doc

Page 41

Image 41
Contents Configuration and Administration NetLink e340/h340/i640 Wireless TelephoneSVP Trademark InformationImportant Safety Information Table of Contents SpectraLink Corporation Model Numbers About This DocumentRelated Documents Customer Support HotlineQoS and Security NetLink Wireless Telephone OverviewSpectraLink Voice Priority SVP Quick Start Guide NetLink e340/h340 Wireless Telephone NetLink Wireless Telephone SpecificationsHandset Display Line indicators Audio featuresStartup Sequence Icon Icons shown in bold turns off whenActive off-hook Handset ModesStandby on-hook Line display Handset DisplaysMenu display FCN displayOpening the Admin menu NetLink Wireless Telephone ConfigurationAdmin Menu To Enter Press Entering and editing Admin menu optionsAlphanumeric string entry Admin Menu Items Nd Level Rd Level Th Level Admin menuPhone Config License Option Essid Select either WEP Off or WEP On Regulatory Domain User-defined Preferences Standby menu item Nd Level Rd Level Th Level Standby menuOff silent PBX PBX determines ring cadence e.g. the PBX may send System Info Current Channel X 1 2 3 4 5 6 7 8 New Channel = ? Requirements License ManagementConfiguration Process Testing a Handset Run Site Survey Diagnostic Tools7 b c Screen Diagnostics ModeSolving coverage issues M m m Screen Message type Errors Events Full Syslog ModeMessages are formatted like the following example Conducting a Site Survey Certifying the HandsetsDownload failure or recovery messages Software MaintenanceUpgrading handsets Normal download messagesConfiguration Problems TroubleshootingAccess Point Problems Dialtone Problems Infrastructure ProblemsMessage Description Action Handset Status MessagesMessage Description Action Do not Power OFF Message Description Action Wireless Telephone Configuration section Message Description Action Index
Related manuals
Manual 29 pages 38.42 Kb