Polycom I640, H340, E340, 72-1065-09 manual Message Description Action

Page 45

 

SpectraLink Corporation

Configuration and Administration–NetLink e340/h340/ i640 Wireless Telephone

 

 

NetLink Telephony Gateway and SpectraLink Radio Protocol

 

 

 

 

 

 

Message

Description

Action

 

 

 

 

 

System Busy

y…y = SVP Server/Telephony Gateway IP

All call paths are in use, try the call again in a

 

yyy.yyy.yyy.yyy

Address

few minutes.

 

 

Gateway or SVP server has reached call

 

 

 

 

capacity; displays IP address of

 

 

 

 

Gateway/SVP Server.

 

 

 

 

 

 

 

System Locked

Gateway is locked.

Try the call again, system has been locked for

 

(with Busy Tone)

 

maintenance.

 

 

 

 

 

TFTP ERROR(x):yy

A failure has occurred during a TFTP

Error code 01, 02, 07 or 16 - check the TFTP

 

 

software download. (x) = The file number

server configuration.

 

 

which was being downloaded; yy is an

Error code 81, the handset will attempt to

 

 

error code describing the particular

 

 

download the file again.

 

 

failure. Possible error codes are:

 

 

For other messages, power off the handset,

 

 

01 = TFTP server did not find the

 

 

then turn it on again to retry the download. If

 

 

requested file.

 

 

the error repeats, note it and contact

 

 

 

 

 

02 = Access violation (reported from TFTP

SpectraLink Technical Support.

 

 

server).

 

 

 

 

07 = TFTP server reported "No such

 

 

 

 

user" error.

 

 

 

 

16 = No TFTP server address

 

 

 

 

81 = File put into memory did not CRC.

 

 

 

 

FF = Timeout error. TFTP server did not

 

 

 

 

respond within a specified period of time.

 

 

 

 

 

 

 

Too many errors

The handset continues to reset and

Fatal error. Return handset to SpectraLink.

 

 

cannot be recovered.

 

 

 

 

 

 

 

Unknown

A phrase is missing from your phintl file.

Download new software from the SpectraLink

 

xx:yy:zz

 

site per section 8 Software Maintenance.

 

 

 

 

 

Updating …

The handset is internally updating its

None. The handset may do this briefly after a

 

 

software images

download. This is informational only.

 

 

 

 

 

Updating Code

Handset is downloading new software

None. When the progress bar fills the display

 

 

into memory. The number icons at the

line the update operation is complete on that

 

 

bottom of the display indicate which file

file.

 

 

number is currently being downloaded.

Do not turn the handset off during this

 

 

This message also displays a progress

 

 

operation.

 

 

bar. When the progress bar fills the

 

 

 

 

 

 

display line the update operation is

 

 

 

 

complete on that file.

 

 

 

 

 

 

 

Use Deskset

Handset is inserted in Docking Station

Not an error. Use the Docking Station or

 

 

cradle.

remove handset from cradle.

 

 

 

 

 

Wrong Code Type

The software loaded into the handset is

Verify the license type is set correctly.

 

 

the wrong type for this model handset.

If the license type is correct, replace the

 

 

 

 

 

 

software image on the TFTP server with the

 

 

 

software that is correct for the handset model.

 

 

 

 

 

Waiting

Handset has attempted some operation

None. The handset is waiting for a specified

 

 

several times and failed, and is now

period of time before attempting that

 

 

waiting for a period of time before

operation again.

 

 

attempting that operation again.

 

 

 

 

 

 

 

PN: 72-1065-09-J.doc

Page 45

Image 45
Contents Configuration and Administration NetLink e340/h340/i640 Wireless TelephoneSVP Trademark InformationImportant Safety Information Table of Contents SpectraLink Corporation Model Numbers About This DocumentRelated Documents Customer Support HotlineNetLink Wireless Telephone Overview SpectraLink Voice Priority SVPQoS and Security Quick Start Guide NetLink e340/h340 Wireless Telephone NetLink Wireless Telephone SpecificationsHandset Display Line indicators Audio featuresStartup Sequence Icon Icons shown in bold turns off whenHandset Modes Standby on-hookActive off-hook Line display Handset DisplaysMenu display FCN displayNetLink Wireless Telephone Configuration Admin MenuOpening the Admin menu Entering and editing Admin menu options Alphanumeric string entryTo Enter Press Admin Menu Items Nd Level Rd Level Th Level Admin menuPhone Config License Option Essid Select either WEP Off or WEP On Regulatory Domain User-defined Preferences Standby menu item Nd Level Rd Level Th Level Standby menuOff silent PBX PBX determines ring cadence e.g. the PBX may send System Info Current Channel X 1 2 3 4 5 6 7 8 New Channel = ? Requirements License ManagementConfiguration Process Testing a Handset Run Site Survey Diagnostic Tools7 b c Diagnostics Mode Solving coverage issuesScreen M m m Screen Message type Errors Events Full Syslog ModeMessages are formatted like the following example Conducting a Site Survey Certifying the HandsetsDownload failure or recovery messages Software MaintenanceUpgrading handsets Normal download messagesTroubleshooting Access Point ProblemsConfiguration Problems Dialtone Problems Infrastructure ProblemsMessage Description Action Handset Status MessagesMessage Description Action Do not Power OFF Message Description Action Wireless Telephone Configuration section Message Description Action Index
Related manuals
Manual 29 pages 38.42 Kb