CyberData 11111, 11113 manual Important Safety Instructions

Page 3

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

13.Prior to installation, consult local building and electrical code requirements.

GENERAL ALERT

Warning

Electrical Hazard: This product should be installed by a licensed electrician according to all local electrical and building codes.

GENERAL ALERT

Warning

Electrical Hazard: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

CyberData Corporation

930500E

Operations Guide

Image 3
Contents Replaces #011111 Document 930500E for Firmware Version VoIP V3 Indoor Intercom Operations GuideCopyright Notice Important Safety Instructions Hazard Levels Pictorial Alert IconsRevision Information Contents Appendix C Troubleshooting/Technical Support IndexA Windows Environment How to Identify This Product Product OverviewModel number Typical System Installation Generic PoE SwitchDoor Strike VoIP Intercom IP Phone IP PBX Server Product Features PoE 802.3af-enabled Powered-over-EthernetConcurrent SIP and multicast paging Supported Protocols Supported SIP ServersIntercom supports This number replaces the 011111 number Product SpecificationsDimensions-Unit Dimensions DimensionsR0.438 R11.1 R0.100 Plcs PCB Dimensions and Intrusion Sensor Range 1illustrates the VoIP V3 Indoor Intercom parts Installing the VoIP V3 Indoor IntercomParts List Intercom Mounting Accessory KitIntercom Components Information about the functionality Call ButtonSpeaker Call Button and Call Button LED Call Button and the Call Button LEDCalling with the The Call Button Call Button LED FunctionIntercom Setup Intercom Connections= Door Sense Ground Reference Connecting the Intercom to the Auxiliary Relay Example of External Relay not supplied Auxiliary Relay Wiring ContactsJ10 Identifying the VoIP Intercom ConnectorsPoE Network Connection RJ-45 ethernet Factory Only-ResetFactory Only-Boot Mode JP10 Disables the intrusion sensor when installedLink Activity Network Connectivity, and Data RateEthernet cable Verify Network Activity Network ConnectorAnnouncing the IP Address Rtfm ButtonRestoring the Factory Default Settings Adjust the VolumeConfigure the Intercom Parameters Factory Default SettingsIP Addressing Intercom Web Page Navigation Log in to the Configuration Home 13. Home Current Settings Device Settings14. Device Configuration Configure the DeviceCall Volume SettingsRelay Settings Miscellaneous SettingsAfter changing the parameters, click the Save button 15. Network Configuration Configure the Network ParametersSelect either Dhcp IP Addressing or Static IP Addressing by Stored Network SettingsDhcp Timeout Current Network SettingsClick SIP Config to open the SIP Configuration page Figure Configure the SIP ParametersBackup SIP Server 1 and Backup SIP Server 2 fields blank Enable SIP Operation Enables or disables SIP operationSIP Settings If all of the Primary SIP Server and Backup SIP ServerDial Out Settings Dial Out Extension Strings and Dtmf Tones using rfc2833After changing the parameters, click Save Settings RTP SettingsIntercom is set to not register with a SiP server Point-to-Point ConfigurationDelayed Dtmf 18. Nightringer Configuration Setup Configure the Nightringer ParametersAfter changing the parameters, click on the Save button Nightringer SettingsConfigure the Sensor Configuration Parameters 19. Sensor Configuration Intrusion Sensor Settings Door Sensor Settings20. Multicast Configuration Configure the Multicast Parameters9.1, Assigning Priority for more details Assigning Priority21. Audio Configuration Configure the Audio Configuration Parameters22. Audio Configuration Audio Files 23. Audacity User-created Audio FilesWAV Microsoft signed 16 bit PCM WAV Microsoft signed 16 bit PCM16shows the web page items on the Event Configuration Configure the Event ParametersWhen selected, Call Terminated Events are enabled Remote Event ServerEvents Example Packets for Events Operations Guide 930500E CyberData Corporation User-Agent CyberData/1.0.0 Content-Length 27. Autoprovisioning Configuration Configure the Autoprovisioning ParametersAutoprovisioning Server IP Address Enable AutoprovisioningAutoprovisioning Get Autoprovisioning from DhcpWould be a valid autoprovisioning file AutoprovisioningOperations Guide 930500E CyberData Corporation Autoprovisioned Audio Files Uploading the Firmware Upgrade the Firmware and Reboot the IntercomFile Upload 18. Firmware Upgrade Parameters Web Page Item DescriptionReboot the Intercom Click Reboot -29. a normal restart will occurReboot Command Interface Post Commands Command InterfacePlay the 4 audio file Wget Play the Intrusion Sensor Triggered audio file WgetPlay the Door Ajar audio file Wget Play the Night Ring audio file Wget Deletedoorajar=yes Delete the Night Ring audio file Wget Delete the Door Ajar audio file WgetSheet Metal Screw Appendix a Mounting the Indoor IntercomWall Mounting Components Quantity Part NameCable Connections Figure A-1shows how to properly connect the VoIP IntercomFigure A-2shows a wall mounting option Wall Mounting OptionDimensions are in Inches Millimeter Wall Cutout DimensionsTop Cable Entry Slot Gang Box OptionPCB Dimensions A Windows Environment Appendix B Setting up a Tftp ServerSet up a Tftp Server A Linux EnvironmentAppendix C Troubleshooting/Technical Support Frequently Asked Questions FAQDocumentation Contact Information Spare in the Air Policy WarrantyWarranty & RMA Returns within the United States Warranty & RMA Returns Outside of the United StatesReturn and Restocking Policy Warranty and RMA ReturnsNumerics IndexIndex SIP Yellow act light 18 yellow link light Srst