CyberData 11113, 11111 manual Volume Settings, Relay Settings, Miscellaneous Settings, Call

Page 34

Installing the VoIP V3 Indoor Intercom 27

Configure the Device

2.On the Device Configuration page, you may enter values for the parameters indicated in Table 2-7.

Table 2-7. Device Configuration Parameters

 

 

Web Page Item

Description

 

 

Volume Settings

 

 

 

Speaker Volume

Type the desired Intercom volume level into this field.

 

 

Microphone Gain

Type the desired microphone gain level into this field.

 

 

Relay Settings

 

 

 

Activate Relay with DTMF Code

When selected, the relay can be activated with a DTMF

 

code.

 

 

DTMF Activation Code

Type the desired DTMF activation code

 

(25 character limit).

 

 

DTMF Activation Duration (in seconds)

Type the desired DTMF activation duration (in seconds) (2

 

character limit [activation times now go up to 99 seconds]).

 

NOTE: A DTMF activation duration of 0 will toggle the

 

relay indefinitely or until the activation code is sent again

 

 

Activate Relay During Ring

When selected, the relay will be activated for as long as

 

the call is active.

 

NOTE: When the phone is set to Auto Answer, it will not

 

ring and this option does nothing.

 

 

Activate Relay During Night Ring

Check this box to activate the relay for as long as a Night

 

Ring tone is ringing.

 

 

Activate Relay While Call Active

When selected, the relay will be activated for as long as

 

the call is active.

 

 

Activate Relay on Button Press

When selected, the relay will be activated when the Call

 

Button is pressed.

 

 

Relay on Button Press Timeout (in seconds)

Type the desired time (in seconds) that you want the relay

 

to activate after the Call Button is pressed (1 character

 

limit).

 

 

Miscellaneous Settings

 

 

 

Auto-Answer Incoming Calls

When selected, the device will automatically answer

 

incoming calls.

 

When Auto Answer is Off, the device will play a ringtone

 

through the Intercom speaker until someone presses the

 

button.

 

 

Button Lit When Idle

When selected, the Call Button remains lit when idle.

 

 

Play Ringback Tone

When selected, you will hear a ringback tone while making

 

a call.

 

 

Operations Guide

930500E

CyberData Corporation

Image 34
Contents VoIP V3 Indoor Intercom Operations Guide Replaces #011111 Document 930500E for Firmware VersionCopyright Notice Important Safety Instructions Pictorial Alert Icons Hazard LevelsRevision Information Contents Index Appendix C Troubleshooting/Technical SupportA Windows Environment Product Overview How to Identify This ProductModel number Generic PoE Switch Typical System InstallationDoor Strike VoIP Intercom IP Phone IP PBX Server PoE 802.3af-enabled Powered-over-Ethernet Product FeaturesConcurrent SIP and multicast paging Supported SIP Servers Supported ProtocolsIntercom supports Product Specifications This number replaces the 011111 numberDimensions Dimensions-Unit DimensionsR0.438 R11.1 R0.100 Plcs PCB Dimensions and Intrusion Sensor Range Intercom Mounting Accessory Kit Installing the VoIP V3 Indoor IntercomParts List 1illustrates the VoIP V3 Indoor Intercom partsInformation about the functionality Call Button Intercom ComponentsSpeaker Call Button LED Function Call Button and the Call Button LEDCalling with the The Call Button Call Button and Call Button LEDIntercom Connections Intercom Setup= Door Sense Ground Reference Connecting the Intercom to the Auxiliary Relay Auxiliary Relay Wiring Contacts Example of External Relay not suppliedIdentifying the VoIP Intercom Connectors J10JP10 Disables the intrusion sensor when installed Factory Only-ResetFactory Only-Boot Mode PoE Network Connection RJ-45 ethernetNetwork Connectivity, and Data Rate Link ActivityEthernet cable Network Connector Verify Network ActivityRtfm Button Announcing the IP AddressAdjust the Volume Restoring the Factory Default SettingsFactory Default Settings Configure the Intercom ParametersIP Addressing Intercom Web Page Navigation Log in to the Configuration Home 13. Home Device Settings Current SettingsConfigure the Device 14. Device ConfigurationMiscellaneous Settings Volume SettingsRelay Settings CallAfter changing the parameters, click the Save button Configure the Network Parameters 15. Network ConfigurationCurrent Network Settings Stored Network SettingsDhcp Timeout Select either Dhcp IP Addressing or Static IP Addressing byConfigure the SIP Parameters Click SIP Config to open the SIP Configuration page FigureIf all of the Primary SIP Server and Backup SIP Server Enable SIP Operation Enables or disables SIP operationSIP Settings Backup SIP Server 1 and Backup SIP Server 2 fields blankRTP Settings Dial Out Extension Strings and Dtmf Tones using rfc2833After changing the parameters, click Save Settings Dial Out SettingsPoint-to-Point Configuration Intercom is set to not register with a SiP serverDelayed Dtmf Configure the Nightringer Parameters 18. Nightringer Configuration SetupNightringer Settings After changing the parameters, click on the Save buttonConfigure the Sensor Configuration Parameters 19. Sensor Configuration Door Sensor Settings Intrusion Sensor SettingsConfigure the Multicast Parameters 20. Multicast ConfigurationAssigning Priority 9.1, Assigning Priority for more detailsConfigure the Audio Configuration Parameters 21. Audio Configuration22. Audio Configuration Audio Files User-created Audio Files 23. AudacityWAV Microsoft signed 16 bit PCM WAV Microsoft signed 16 bit PCMConfigure the Event Parameters 16shows the web page items on the Event ConfigurationRemote Event Server When selected, Call Terminated Events are enabledEvents Example Packets for Events Operations Guide 930500E CyberData Corporation User-Agent CyberData/1.0.0 Content-Length Configure the Autoprovisioning Parameters 27. Autoprovisioning ConfigurationGet Autoprovisioning from Dhcp Enable AutoprovisioningAutoprovisioning Autoprovisioning Server IP AddressAutoprovisioning Would be a valid autoprovisioning fileOperations Guide 930500E CyberData Corporation Autoprovisioned Audio Files Upgrade the Firmware and Reboot the Intercom Uploading the Firmware18. Firmware Upgrade Parameters Web Page Item Description File UploadClick Reboot -29. a normal restart will occur Reboot the IntercomReboot Command Interface Command Interface Post CommandsPlay the Intrusion Sensor Triggered audio file Wget Play the 4 audio file WgetPlay the Door Ajar audio file Wget Play the Night Ring audio file Wget Delete the Door Ajar audio file Wget Deletedoorajar=yes Delete the Night Ring audio file WgetQuantity Part Name Appendix a Mounting the Indoor IntercomWall Mounting Components Sheet Metal ScrewFigure A-1shows how to properly connect the VoIP Intercom Cable ConnectionsWall Mounting Option Figure A-2shows a wall mounting optionWall Cutout Dimensions Dimensions are in Inches MillimeterGang Box Option Top Cable Entry SlotPCB Dimensions A Linux Environment Appendix B Setting up a Tftp ServerSet up a Tftp Server A Windows EnvironmentFrequently Asked Questions FAQ Appendix C Troubleshooting/Technical SupportDocumentation Contact Information Warranty & RMA Returns Outside of the United States WarrantyWarranty & RMA Returns within the United States Spare in the Air PolicyWarranty and RMA Returns Return and Restocking PolicyIndex NumericsIndex SIP Srst Yellow act light 18 yellow link light