CyberData Guide to Uploading Firmware for VoIP V3 Indoor Intercom Systems

Page 65

Installing the VoIP V3 Indoor Intercom 58

Uploading the Firmware

2.5 Upgrade the Firmware and Reboot the Intercom

GENERAL ALERT

Caution

Equipment Hazard: V3 devices like the VoIP V3 Indoor Intercom cannot use firmware 6.x.x or earlier, and older V1 and V2 devices cannot use firmware 7.x.x or later.

2.5.1 Uploading the Firmware

To upload the firmware from your computer:

1.Retrieve the latest Intercom firmware file from the VoIP V3 Indoor Intercom Downloads page at: http://www.cyberdata.net/products/voip/digitalanalog/intercomindoorv3/downloads.html

2.Unzip the firmware version file. This file may contain the following:

•Firmware file

•Release notes

3.Log in to the Intercom home page as instructed in Section 2.4.3, "Log in to the Configuration Home Page".

4.Click the Update Firmware button to open the Upgrade Firmware page. See Figure 2-28.

Operations Guide

930500E

CyberData Corporation

Image 65

Contents Replaces #011111 Document 930500E for Firmware Version VoIP V3 Indoor Intercom Operations GuideCopyright Notice Important Safety Instructions Hazard Levels Pictorial Alert IconsRevision Information Contents A Windows Environment Appendix C Troubleshooting/Technical SupportIndex Model number How to Identify This ProductProduct Overview Door Strike VoIP Intercom IP Phone IP PBX Server Typical System InstallationGeneric PoE Switch Concurrent SIP and multicast paging Product FeaturesPoE 802.3af-enabled Powered-over-Ethernet Intercom supports Supported ProtocolsSupported SIP Servers This number replaces the 011111 number Product SpecificationsDimensions-Unit Dimensions DimensionsR0.438 R11.1 R0.100 Plcs PCB Dimensions and Intrusion Sensor Range Parts List Installing the VoIP V3 Indoor IntercomIntercom Mounting Accessory Kit 1illustrates the VoIP V3 Indoor Intercom partsSpeaker Intercom ComponentsInformation about the functionality Call Button Calling with the The Call Button Call Button and the Call Button LEDCall Button LED Function Call Button and Call Button LED= Door Sense Ground Reference Intercom SetupIntercom Connections Connecting the Intercom to the Auxiliary Relay Example of External Relay not supplied Auxiliary Relay Wiring ContactsJ10 Identifying the VoIP Intercom ConnectorsFactory Only-Boot Mode Factory Only-ResetJP10 Disables the intrusion sensor when installed PoE Network Connection RJ-45 ethernetEthernet cable Link ActivityNetwork Connectivity, and Data Rate Verify Network Activity Network ConnectorAnnouncing the IP Address Rtfm ButtonRestoring the Factory Default Settings Adjust the VolumeIP Addressing Configure the Intercom ParametersFactory Default Settings Intercom Web Page Navigation Log in to the Configuration Home 13. Home Current Settings Device Settings14. Device Configuration Configure the DeviceRelay Settings Volume SettingsMiscellaneous Settings CallAfter changing the parameters, click the Save button 15. Network Configuration Configure the Network ParametersDhcp Timeout Stored Network SettingsCurrent Network Settings Select either Dhcp IP Addressing or Static IP Addressing byClick SIP Config to open the SIP Configuration page Figure Configure the SIP ParametersSIP Settings Enable SIP Operation Enables or disables SIP operationIf all of the Primary SIP Server and Backup SIP Server Backup SIP Server 1 and Backup SIP Server 2 fields blankAfter changing the parameters, click Save Settings Dial Out Extension Strings and Dtmf Tones using rfc2833RTP Settings Dial Out SettingsIntercom is set to not register with a SiP server Point-to-Point ConfigurationDelayed Dtmf 18. Nightringer Configuration Setup Configure the Nightringer ParametersAfter changing the parameters, click on the Save button Nightringer SettingsConfigure the Sensor Configuration Parameters 19. Sensor Configuration Intrusion Sensor Settings Door Sensor Settings20. Multicast Configuration Configure the Multicast Parameters9.1, Assigning Priority for more details Assigning Priority21. Audio Configuration Configure the Audio Configuration Parameters22. Audio Configuration Audio Files 23. Audacity User-created Audio FilesWAV Microsoft signed 16 bit PCM WAV Microsoft signed 16 bit PCM16shows the web page items on the Event Configuration Configure the Event ParametersEvents When selected, Call Terminated Events are enabledRemote Event Server Example Packets for Events Operations Guide 930500E CyberData Corporation User-Agent CyberData/1.0.0 Content-Length 27. Autoprovisioning Configuration Configure the Autoprovisioning ParametersAutoprovisioning Enable AutoprovisioningGet Autoprovisioning from Dhcp Autoprovisioning Server IP AddressWould be a valid autoprovisioning file AutoprovisioningOperations Guide 930500E CyberData Corporation Autoprovisioned Audio Files Uploading the Firmware Upgrade the Firmware and Reboot the IntercomFile Upload 18. Firmware Upgrade Parameters Web Page Item DescriptionReboot Reboot the IntercomClick Reboot -29. a normal restart will occur Command Interface Post Commands Command InterfacePlay the Door Ajar audio file Wget Play the 4 audio file WgetPlay the Intrusion Sensor Triggered audio file Wget Play the Night Ring audio file Wget Deletedoorajar=yes Delete the Night Ring audio file Wget Delete the Door Ajar audio file WgetWall Mounting Components Appendix a Mounting the Indoor IntercomQuantity Part Name Sheet Metal ScrewCable Connections Figure A-1shows how to properly connect the VoIP IntercomFigure A-2shows a wall mounting option Wall Mounting OptionDimensions are in Inches Millimeter Wall Cutout DimensionsTop Cable Entry Slot Gang Box OptionPCB Dimensions Set up a Tftp Server Appendix B Setting up a Tftp ServerA Linux Environment A Windows EnvironmentDocumentation Appendix C Troubleshooting/Technical SupportFrequently Asked Questions FAQ Contact Information Warranty & RMA Returns within the United States WarrantyWarranty & RMA Returns Outside of the United States Spare in the Air PolicyReturn and Restocking Policy Warranty and RMA ReturnsNumerics IndexIndex SIP Yellow act light 18 yellow link light Srst