CyberData 11111, 11113 manual Stored Network Settings, Dhcp Timeout, Current Network Settings

Page 37

Installing the VoIP V3 Indoor Intercom 30

Configure the Network Parameters

2. On the Network Configuration page, enter values for the parameters indicated in Table 2-8.

Table 2-8. Network Configuration Parameters

 

 

Web Page Item

Description

 

 

Stored Network Settings

 

 

 

IP Addressing

Select either DHCP IP Addressing or Static IP Addressing by

 

marking the appropriate radio button. If you select Static, configure

 

the remaining parameters indicated in Table 2-8. If you select DHCP,

 

go to Step 3.

 

 

IP Address

Enter the Static IP address.

 

 

Subnet Mask

Enter the Subnet Mask address.

 

 

Default Gateway

Enter the Default Gateway address.

 

 

DNS Server 1

Enter the DNS Server 1 address.

 

 

DNS Server 2

Enter the DNS Server 2 address.

 

 

DHCP Timeout

 

 

 

DHCP Timeout in seconds

Enter the desired timeout duration (in seconds) that the device will

 

wait for a response from the DHCP server before defaulting back to

 

the stored static IP address.

 

Note: A value of -1will cause the device to retry indefinitely and a

 

value of 0 will cause the device to reset to a default of 60 seconds.

 

 

Current Network Settings

Shows the current network settings.

 

 

IP Address

Shows the current Static IP address.

 

 

Subnet Mask

Shows the current Subnet Mask address.

 

 

Default Gateway

Shows the current Default Gateway address.

 

 

DNS Server 1

Shows the current DNS Server 1 address.

 

 

DNS Server 2

Shows the current DNS Server 2 address.

 

 

 

Click the Save button to save your configuration settings.

 

Note: You need to reboot for changes to take effect.

 

 

 

Click on the Reboot button to reboot the system.

3.After changing the parameters, click Save Settings. This updates the changed parameters and reboots the Intercom if appropriate.

4.Connect the Intercom to the target network.

5.From a system on the same network as the Intercom, open a browser with the new IP address of the Intercom.

Operations Guide

930500E

CyberData Corporation

Image 37
Contents Replaces #011111 Document 930500E for Firmware Version VoIP V3 Indoor Intercom Operations GuideCopyright Notice Important Safety Instructions Hazard Levels Pictorial Alert IconsRevision Information Contents Index Appendix C Troubleshooting/Technical SupportA Windows Environment Product Overview How to Identify This ProductModel number Generic PoE Switch Typical System InstallationDoor Strike VoIP Intercom IP Phone IP PBX Server PoE 802.3af-enabled Powered-over-Ethernet Product FeaturesConcurrent SIP and multicast paging Supported SIP Servers Supported ProtocolsIntercom supports This number replaces the 011111 number Product SpecificationsDimensions-Unit Dimensions DimensionsR0.438 R11.1 R0.100 Plcs PCB Dimensions and Intrusion Sensor Range Parts List Installing the VoIP V3 Indoor IntercomIntercom Mounting Accessory Kit 1illustrates the VoIP V3 Indoor Intercom partsInformation about the functionality Call Button Intercom ComponentsSpeaker Calling with the The Call Button Call Button and the Call Button LEDCall Button LED Function Call Button and Call Button LEDIntercom Connections Intercom Setup= Door Sense Ground Reference Connecting the Intercom to the Auxiliary Relay Example of External Relay not supplied Auxiliary Relay Wiring ContactsJ10 Identifying the VoIP Intercom ConnectorsFactory Only-Boot Mode Factory Only-ResetJP10 Disables the intrusion sensor when installed PoE Network Connection RJ-45 ethernetNetwork Connectivity, and Data Rate Link ActivityEthernet cable Verify Network Activity Network ConnectorAnnouncing the IP Address Rtfm ButtonRestoring the Factory Default Settings Adjust the VolumeFactory Default Settings Configure the Intercom ParametersIP Addressing Intercom Web Page Navigation Log in to the Configuration Home 13. Home Current Settings Device Settings14. Device Configuration Configure the DeviceRelay Settings Volume SettingsMiscellaneous Settings CallAfter changing the parameters, click the Save button 15. Network Configuration Configure the Network ParametersDhcp Timeout Stored Network SettingsCurrent Network Settings Select either Dhcp IP Addressing or Static IP Addressing byClick SIP Config to open the SIP Configuration page Figure Configure the SIP ParametersSIP Settings Enable SIP Operation Enables or disables SIP operationIf all of the Primary SIP Server and Backup SIP Server Backup SIP Server 1 and Backup SIP Server 2 fields blankAfter changing the parameters, click Save Settings Dial Out Extension Strings and Dtmf Tones using rfc2833RTP Settings Dial Out SettingsIntercom is set to not register with a SiP server Point-to-Point ConfigurationDelayed Dtmf 18. Nightringer Configuration Setup Configure the Nightringer ParametersAfter changing the parameters, click on the Save button Nightringer SettingsConfigure the Sensor Configuration Parameters 19. Sensor Configuration Intrusion Sensor Settings Door Sensor Settings20. Multicast Configuration Configure the Multicast Parameters9.1, Assigning Priority for more details Assigning Priority21. Audio Configuration Configure the Audio Configuration Parameters22. Audio Configuration Audio Files 23. Audacity User-created Audio FilesWAV Microsoft signed 16 bit PCM WAV Microsoft signed 16 bit PCM16shows the web page items on the Event Configuration Configure the Event ParametersRemote Event Server When selected, Call Terminated Events are enabledEvents Example Packets for Events Operations Guide 930500E CyberData Corporation User-Agent CyberData/1.0.0 Content-Length 27. Autoprovisioning Configuration Configure the Autoprovisioning ParametersAutoprovisioning Enable AutoprovisioningGet Autoprovisioning from Dhcp Autoprovisioning Server IP AddressWould be a valid autoprovisioning file AutoprovisioningOperations Guide 930500E CyberData Corporation Autoprovisioned Audio Files Uploading the Firmware Upgrade the Firmware and Reboot the IntercomFile Upload 18. Firmware Upgrade Parameters Web Page Item DescriptionClick Reboot -29. a normal restart will occur Reboot the IntercomReboot Command Interface Post Commands Command InterfacePlay the Intrusion Sensor Triggered audio file Wget Play the 4 audio file WgetPlay the Door Ajar audio file Wget Play the Night Ring audio file Wget Deletedoorajar=yes Delete the Night Ring audio file Wget Delete the Door Ajar audio file WgetWall Mounting Components Appendix a Mounting the Indoor IntercomQuantity Part Name Sheet Metal ScrewCable Connections Figure A-1shows how to properly connect the VoIP IntercomFigure A-2shows a wall mounting option Wall Mounting OptionDimensions are in Inches Millimeter Wall Cutout DimensionsTop Cable Entry Slot Gang Box OptionPCB Dimensions Set up a Tftp Server Appendix B Setting up a Tftp ServerA Linux Environment A Windows EnvironmentFrequently Asked Questions FAQ Appendix C Troubleshooting/Technical SupportDocumentation Contact Information Warranty & RMA Returns within the United States WarrantyWarranty & RMA Returns Outside of the United States Spare in the Air PolicyReturn and Restocking Policy Warranty and RMA ReturnsNumerics IndexIndex SIP Yellow act light 18 yellow link light Srst