Panasonic KX-TCD961CXB operating instructions Answering Calls, To redial the last number dialed

Page 23

KX-TCD961CXB(22~27) 99.12.3 2:08 PM Page 23

To redial the last number dialed

Press ➡ .

•The last number dialed is automatically redialed.

To redial after confirming the numbers in redial memory

The unit automatically stores the last 10 numbers dialed into redial memory.

1Press .

•The last number dialed is displayed.

2Select the desired number by pressing

.

•You can also search from the most recent to oldest number by pressing G. To search from the oldest to most recent number, press F.

•“----------”denotes the end of redial memory.

•To exit the list, press C firmly.

3 Press .

•The number is dialed automatically.

•If your line has rotary or pulse service, any

access numbers entered after pressing will not be included when redialing.

To clear all of the numbers in the redial memory

1 Press .

2Press G or F until “ ” is displayed, then press O K .

3Press .

•A confirmation tone sounds and the display will return to the stand-by mode.

Chapter 2 Cordless Telephone

Answering Calls

Make sure that the power is ON (p. 13), otherwise the handset will not ring.

(Basic

If the handset is off the base unit, press

.

•You can also answer a call by pressing any

dialing button 0 to 9 , or (—Any Key Talk).

OR

If on the base unit, just lift up.

•The handset and base unit will not ring if both ringer volumes are set to OFF (p. 14, 15).

To turn the handset ringer off temporarily

When the handset starts ringing, press G firmly.

•“ ” is displayed and the handset stops ringing.

•The ringer will turn back on for the next call.

•This function will not work when the handset is on the base unit.

Operations)

23

Image 23

Contents Charge the batteries for about 4 hours before initial use Operating InstructionsName and address of dealer Battery p One Three Handset Cover p Belt Clip pBefore Initial Use Serial No Date of purchaseObstructions such as walls Battery ChargeFor Best Performance Base Unit LocationContents Correct Use and Charging Selecting the Stand-by ModeNew Message Button Select Button p Skip Button Charge IndicatorLocation of Controls Base unitTone Button Handset13, 18, 24, 27 Recording time is set to greeting only p DisplaysBase unit display Messages have been recordedIs pressed while dialing Display shows all possible configurationsIcons CharactersTo remove the belt clip SettingsInstalling the Batteries in the Handset Using the Belt ClipTelephone ConnectionsRecharge Settings Battery ChargeBattery strength Battery informationPress Turning the Power onSelecting the Dialing Mode Press firmlyF23 Settings Selecting the Handset Ringer Volume/PatternRinger volume IUU23U Selecting the Base Unit Ringer Volume/Pattern22u2 To select to Slovakian, press To select to Czech, press Preparing the Answering SystemSelecting the Voice Guidance Language Greeting Message Function p Function itemTime p To set the greeting monitorPress repeatedly to set the day Time and Day AdjustmentTo check the time/day Recording time MinutesGreeting only Selecting the Number of Rings Setting the Greeting Monitor FunctionPress Toll Saver When set to Auto Current setting, 1 or 2, is displayed on the base unit00 00 To select the receiver volumeMaking Calls I2345678To turn the handset ringer off temporarily Answering CallsTo redial the last number dialed To redial after confirming the numbers in redial memoryTo erase a stored number Speed DialerStoring Phone Numbers in Memory Dialing a Stored NumberPaging the handset from the base unit Handset locator IntercomPaging the base unit from the handset To select 5 seconds, press To select 3 seconds, press Press Special FeaturesHow to Use the Pause Feature Setting the pause timingTo cancel the key lock Setting the Key LockUsing the Recall Feature For Rotary or Pulse Service UsersSummary of Programmable Functions 5o - - o Setting the PasswordF5o F5o - - oF42 Setting the Direct Call ModeTo turn OFF the direct call mode Direct CallF4 IO0 To turn OFF the call prohibition modeCall Prohibition F4 IoI23456 To cancel the call restricted handsetsTo cancel the call restriction numbers Call RestrictionDuring a conversation, the display will be as follows Selecting the Talk Mode DisplayPress G or F to select the desired setting F32UAutomatic Route Selection To store the area codes Storing the Carrier Code/Area CodesTo store the carrier code F26 Other Programmable SettingsF2 i F25Function Clearing the Settings in MemoryPress Answer on to turn on the answering system Setting the Unit to Answer CallsAutomatic Answering Operation Monitoring incoming callsListening to all recorded messages Flash Memory Message BackupListening to Messages Listening to only new messagesErasing all messages Erasing MessagesRecording a Memo Message Erasing a specific messageSummary of remote operation Remote Operation from a Touch Tone PhoneDisplay goes out Canceling the remote operationTo cancel, reprogram a new remote code Direct Remote Operation Direct commandsSkipping the greeting message Remote Operation from a Touch Tone PhoneTo continue the remote operation Turning on the answering systemMenu Remote Operation with the HandsetHelp menu During a conversation, press Then Recording your telephone conversation using the handsetContinue your conversation When finished, press then Remote Operation with the HandsetOperating More than One Base Unit For Optional Multi-Unit UsersOperating More than One Handset Registering a Handset in the Base Unit RegistrationF7 i I000 Selecting the Base Unit AccessAutomatic base unit access Specified base unit accessF70 i2 Registration Canceling a HandsetCanceling a base unit Iu2 Selecting the Stand-by Mode DisplayBell Selection F3 i0Enter the handset number you want to ring Bell SelectionSelecting first handset Selecting all handsetsPage, then press Intercom between the Handsets and the Base UnitPaging all the handsets from the base unit All paging Paging a handset from the base unit Individual pagingHandset 1 Press I N T Enter the desired handset number Handset When the unit rings, press to answer00 00 0 Intercom Intercom between HandsetsTransferring a call without the intercom Transferring a call using the intercomTransferring a Call from One Handset to Another Press Press G or F until F24 is displayed Press O K Setting the Call Waiting ToneF24 Intercom ConferenceReplacing the Batteries Selecting the battery typeBattery replacement After replacementReplacing the Batteries Before Requesting Help Cordless Telephone Problem RemedyDoes not function Problem RemedyBefore Requesting Help Answering System Problem Remedy System from a touch tone phone Base unit, it suddenly stops Use indicatorYou cannot operate the answering System at the base unitGeneral Problem Remedy Placement Safety InstructionsSafety Installations EnvironmentLightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions PQQX12234ZA-UK WU1299NR0 Obchodní oddélení Panasonic Czech Republic, s.r.oKrakovská 9, 110 00, Praha 1, Èeská republika Výrobní závod