Panasonic KX-TCD961CXB Call Restriction, I23456, To cancel the call restricted handsets

Page 32

KX-TCD961CXB(28~33) 99.12.3 2:15 PM Page 32

Call Restriction

You can restrict desired handset(s) from dialing selected phone numbers. Phone numbers beginning with the restricted digits cannot be dialed out. For example, if “00” is assigned as the call restriction number, international calls cannot be made.

For selected handset(s), you can assign up to 6 call restriction numbers (up to 8 digits). Set the call restricted handset(s) and the restriction number(s) by programming. The factory preset is OFF.

1 Press then I N T . 2 Press 6 .

3Enter the base unit password (p. 29).

•The current registered handset number(s) is/are displayed.

Ex. Handset 1, 2, 3, 4, 5 and 6 are registered.

6 I23456

4Enter the desired handset number(s).

•The selected handset number(s) flash(es). Ex. Handset 2 and 6 are selected.

6I23456

•If you misdial, press the number(s) again.

5 Press .

•“ I ” is displayed.

6 I -

6Enter a call restriction number, up to 8 digits.

• If you misdial, press C . The digits are erased from the right. To erase all digits, press C firmly.

7 Press .

•A confirmation tone sounds.

•“2 ” is displayed. To continue entering a

number, enter the next number, then press

.

8 Press .

•A confirmation tone sounds and the display will return to the stand-by mode.

When you dial a restricted number,

the call is disconnected, and the dialed number flashes.

Ex. The restricted number is “00”.

00

To cancel the call restricted handset(s)

Follow steps 1 to 3, then enter the handset number(s) you want to cancel. When

finished, press repeatedly until the handset returns to the stand-by mode.

To cancel the call restriction number(s)

Follow steps 1 to 4, then select the call restriction number you want to cancel by

pressing . Then press C . When

finished, press repeatedly until the handset returns to the stand-by mode.

32

Image 32

Contents Operating Instructions Charge the batteries for about 4 hours before initial useBattery p One Three Handset Cover p Belt Clip p Before Initial UseSerial No Date of purchase Name and address of dealerBattery Charge For Best PerformanceBase Unit Location Obstructions such as wallsContents Selecting the Stand-by Mode Correct Use and ChargingSelect Button p Skip Button Charge Indicator Location of ControlsBase unit New Message ButtonTone Button Handset13, 18, 24, 27 Displays Base unit displayMessages have been recorded Recording time is set to greeting only pDisplay shows all possible configurations IconsCharacters Is pressed while dialingSettings Installing the Batteries in the HandsetUsing the Belt Clip To remove the belt clipConnections TelephoneSettings Battery Charge Battery strengthBattery information RechargeTurning the Power on Selecting the Dialing ModePress firmly PressSettings Selecting the Handset Ringer Volume/Pattern Ringer volumeIUU F2323U Selecting the Base Unit Ringer Volume/Pattern22u2 To select to Slovakian, press To select to Czech, press Preparing the Answering SystemSelecting the Voice Guidance Language Greeting Message Function item Time pTo set the greeting monitor Function pPress repeatedly to set the day Time and Day AdjustmentTo check the time/day Recording time MinutesGreeting only Setting the Greeting Monitor Function Press Toll Saver When set to AutoCurrent setting, 1 or 2, is displayed on the base unit Selecting the Number of RingsTo select the receiver volume Making CallsI2345678 00 00Answering Calls To redial the last number dialedTo redial after confirming the numbers in redial memory To turn the handset ringer off temporarilySpeed Dialer Storing Phone Numbers in MemoryDialing a Stored Number To erase a stored numberPaging the handset from the base unit Handset locator IntercomPaging the base unit from the handset Special Features How to Use the Pause FeatureSetting the pause timing To select 5 seconds, press To select 3 seconds, press PressSetting the Key Lock Using the Recall FeatureFor Rotary or Pulse Service Users To cancel the key lockSummary of Programmable Functions Setting the Password F5oF5o - - o 5o - - oSetting the Direct Call Mode To turn OFF the direct call modeDirect Call F42To turn OFF the call prohibition mode Call ProhibitionF4 Io F4 IO0To cancel the call restricted handsets To cancel the call restriction numbersCall Restriction I23456Selecting the Talk Mode Display Press G or F to select the desired settingF32U During a conversation, the display will be as followsAutomatic Route Selection To store the area codes Storing the Carrier Code/Area CodesTo store the carrier code Other Programmable Settings F2 iF25 F26Clearing the Settings in Memory FunctionSetting the Unit to Answer Calls Automatic Answering OperationMonitoring incoming calls Press Answer on to turn on the answering systemFlash Memory Message Backup Listening to MessagesListening to only new messages Listening to all recorded messagesErasing Messages Recording a Memo MessageErasing a specific message Erasing all messagesRemote Operation from a Touch Tone Phone Summary of remote operationDisplay goes out Canceling the remote operationTo cancel, reprogram a new remote code Direct commands Direct Remote OperationRemote Operation from a Touch Tone Phone To continue the remote operationTurning on the answering system Skipping the greeting messageMenu Remote Operation with the HandsetHelp menu Recording your telephone conversation using the handset Continue your conversation When finished, press thenRemote Operation with the Handset During a conversation, press ThenOperating More than One Base Unit For Optional Multi-Unit UsersOperating More than One Handset Registering a Handset in the Base Unit RegistrationF7 i Selecting the Base Unit Access Automatic base unit accessSpecified base unit access I000F70 i2 Registration Canceling a HandsetCanceling a base unit Selecting the Stand-by Mode Display Bell SelectionF3 i0 Iu2Bell Selection Selecting first handsetSelecting all handsets Enter the handset number you want to ringIntercom between the Handsets and the Base Unit Paging all the handsets from the base unit All pagingPaging a handset from the base unit Individual paging Page, then pressHandset When the unit rings, press to answer 00 00 0Intercom Intercom between Handsets Handset 1 Press I N T Enter the desired handset numberTransferring a call without the intercom Transferring a call using the intercomTransferring a Call from One Handset to Another Setting the Call Waiting Tone F24Intercom Conference Press Press G or F until F24 is displayed Press O KSelecting the battery type Battery replacementAfter replacement Replacing the BatteriesReplacing the Batteries Cordless Telephone Problem Remedy Before Requesting HelpDoes not function Problem RemedyBefore Requesting Help Answering System Problem Remedy Base unit, it suddenly stops Use indicator You cannot operate the answeringSystem at the base unit System from a touch tone phoneGeneral Problem Remedy Safety Instructions SafetyInstallations Environment PlacementLightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Obchodní oddélení Panasonic Czech Republic, s.r.o Krakovská 9, 110 00, Praha 1, Èeská republikaVýrobní závod PQQX12234ZA-UK WU1299NR0