Panasonic KX-TCD961CXB Remote Operation with the Handset, During a conversation, press Then

Page 46

KX-TCD961CXB(38~46) 99.12.3 2:19 PM Page 46

Remote Operation with the Handset

Direct commands

	4	NEW MESSAGE PLAYBACK
	4	• Only new messages are played
		back.
	5	ALL MESSAGE PLAYBACK
	5	• All messages are played back.
		• All messages are played back.
	1	REPEAT (During playback)
	1	• The current message is repeated.
		• The current message is repeated.
	2	SKIP (During playback)
	2	• The current message is skipped.
		The next message is played.
	9	STOP (During playback)

• Playback is temporarily stopped.

• To resume playback, press 9 again within 15 seconds, or the help menu (p. 45) will start.

0

8

4	ERASING A SPECIFIC MESSAGE
	(During playback)

•The current message is erased.

•A short beep will sound and the next message will be played.

5 ERASING ALL MESSAGES

•All recorded messages are erased.

•A long beep sound and “No message” are heard.

ANSWERING SYSTEM OFF

•The answering system is turned off and will not answer calls until turned on again.

ANSWERING SYSTEM ON

•The answering system is turned on and is in the stand-by mode for receiving calls.

Recording your telephone conversation using the handset

You can record a telephone conversation.

1During a conversation, press

then .

•“” is displayed on the handset.

2Continue your conversation.

3When finished, press then .

•When you record your 2-way telephone conversation, you should inform the other party that the conversation is being recorded.

•If “” goes out, memory may be full.

46

Image 46

Contents Operating Instructions Charge the batteries for about 4 hours before initial useSerial No Date of purchase Battery p One Three Handset Cover p Belt Clip pBefore Initial Use Name and address of dealerBase Unit Location Battery ChargeFor Best Performance Obstructions such as wallsContents Selecting the Stand-by Mode Correct Use and ChargingBase unit Select Button p Skip Button Charge IndicatorLocation of Controls New Message Button13, 18, 24, 27 HandsetTone Button Messages have been recorded DisplaysBase unit display Recording time is set to greeting only pCharacters Display shows all possible configurationsIcons Is pressed while dialingUsing the Belt Clip SettingsInstalling the Batteries in the Handset To remove the belt clipConnections TelephoneBattery information Settings Battery ChargeBattery strength RechargePress firmly Turning the Power onSelecting the Dialing Mode PressIUU Settings Selecting the Handset Ringer Volume/PatternRinger volume F2322u2 Selecting the Base Unit Ringer Volume/Pattern23U Selecting the Voice Guidance Language Preparing the Answering SystemTo select to Slovakian, press To select to Czech, press Greeting Message To set the greeting monitor Function itemTime p Function pTo check the time/day Time and Day AdjustmentPress repeatedly to set the day Greeting only MinutesRecording time Current setting, 1 or 2, is displayed on the base unit Setting the Greeting Monitor FunctionPress Toll Saver When set to Auto Selecting the Number of RingsI2345678 To select the receiver volumeMaking Calls 00 00To redial after confirming the numbers in redial memory Answering CallsTo redial the last number dialed To turn the handset ringer off temporarilyDialing a Stored Number Speed DialerStoring Phone Numbers in Memory To erase a stored numberPaging the base unit from the handset IntercomPaging the handset from the base unit Handset locator Setting the pause timing Special FeaturesHow to Use the Pause Feature To select 5 seconds, press To select 3 seconds, press PressFor Rotary or Pulse Service Users Setting the Key LockUsing the Recall Feature To cancel the key lockSummary of Programmable Functions F5o - - o Setting the PasswordF5o 5o - - oDirect Call Setting the Direct Call ModeTo turn OFF the direct call mode F42F4 Io To turn OFF the call prohibition modeCall Prohibition F4 IO0Call Restriction To cancel the call restricted handsetsTo cancel the call restriction numbers I23456F32U Selecting the Talk Mode DisplayPress G or F to select the desired setting During a conversation, the display will be as followsAutomatic Route Selection To store the carrier code Storing the Carrier Code/Area CodesTo store the area codes F25 Other Programmable SettingsF2 i F26Clearing the Settings in Memory FunctionMonitoring incoming calls Setting the Unit to Answer CallsAutomatic Answering Operation Press Answer on to turn on the answering systemListening to only new messages Flash Memory Message BackupListening to Messages Listening to all recorded messagesErasing a specific message Erasing MessagesRecording a Memo Message Erasing all messagesRemote Operation from a Touch Tone Phone Summary of remote operationTo cancel, reprogram a new remote code Canceling the remote operationDisplay goes out Direct commands Direct Remote OperationTurning on the answering system Remote Operation from a Touch Tone PhoneTo continue the remote operation Skipping the greeting messageHelp menu Remote Operation with the HandsetMenu Remote Operation with the Handset Recording your telephone conversation using the handsetContinue your conversation When finished, press then During a conversation, press ThenOperating More than One Handset For Optional Multi-Unit UsersOperating More than One Base Unit F7 i RegistrationRegistering a Handset in the Base Unit Specified base unit access Selecting the Base Unit AccessAutomatic base unit access I000Canceling a base unit Registration Canceling a HandsetF70 i2 F3 i0 Selecting the Stand-by Mode DisplayBell Selection Iu2Selecting all handsets Bell SelectionSelecting first handset Enter the handset number you want to ringPaging a handset from the base unit Individual paging Intercom between the Handsets and the Base UnitPaging all the handsets from the base unit All paging Page, then pressIntercom Intercom between Handsets Handset When the unit rings, press to answer00 00 0 Handset 1 Press I N T Enter the desired handset numberTransferring a Call from One Handset to Another Transferring a call using the intercomTransferring a call without the intercom Intercom Conference Setting the Call Waiting ToneF24 Press Press G or F until F24 is displayed Press O KAfter replacement Selecting the battery typeBattery replacement Replacing the BatteriesReplacing the Batteries Cordless Telephone Problem Remedy Before Requesting HelpBefore Requesting Help Problem RemedyDoes not function Answering System Problem Remedy System at the base unit Base unit, it suddenly stops Use indicatorYou cannot operate the answering System from a touch tone phoneGeneral Problem Remedy Installations Environment Safety InstructionsSafety PlacementLightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Výrobní závod Obchodní oddélení Panasonic Czech Republic, s.r.oKrakovská 9, 110 00, Praha 1, Èeská republika PQQX12234ZA-UK WU1299NR0