Panasonic KX-TCD961CXB Registration, F7 i, Registering a Handset in the Base Unit

Page 48

KX-TCD961CXB(47~56) 99.12.3 2:20 PM Page 48

Registration

Registering a Handset in the Base Unit

You must register the handset in the base unit before use.

•Charge the optional handset batteries for about 4 hours before initial use.

•Make sure that the power is ON (p. 13) and the unit is in the stand-by mode.

•Register the handset number within 1 minute. If not registered within 1 minute, press on the handset to cancel the programming mode. Then start again from step 1.

1Base unit where handset is to be

registered:

Press and hold on the base unit for more than 10 seconds until the in

use indicator ( ) lights and a confirmation tone sounds.

2Handset:

Press .

3Press G or F until “F7 i ” is displayed.

4Press O K .

•The available base unit numbers are displayed.

F7 i i234

5 Press the desired base unit number 1 to 4 .

•The number is assigned as the base unit number for the handset.

•While the handset is searching for the base unit, “- ” flashes across on the display.

6Enter the base unit password (p. 29).

F7 i - - - -

7 Press .

•A confirmation tone sounds and the display will return to the stand-by mode.

•The in use indicator ( ) on the base unit will go out.

•To register the handset in more than one base unit, repeat from step 1 with the other base unit(s).

•The base unit number which the handset is currently in contact with can be displayed in the stand-by mode (p. 51). Calls (both incoming and outgoing) can be conducted only via the displayed base unit (even if the radio areas overlap with neighbouring base units).

-

48

Image 48

Contents Operating Instructions Charge the batteries for about 4 hours before initial useBattery p One Three Handset Cover p Belt Clip p Before Initial UseSerial No Date of purchase Name and address of dealerBattery Charge For Best PerformanceBase Unit Location Obstructions such as wallsContents Selecting the Stand-by Mode Correct Use and ChargingSelect Button p Skip Button Charge Indicator Location of ControlsBase unit New Message ButtonHandset 13, 18, 24, 27Tone Button Displays Base unit displayMessages have been recorded Recording time is set to greeting only pDisplay shows all possible configurations IconsCharacters Is pressed while dialingSettings Installing the Batteries in the HandsetUsing the Belt Clip To remove the belt clipConnections TelephoneSettings Battery Charge Battery strengthBattery information RechargeTurning the Power on Selecting the Dialing ModePress firmly PressSettings Selecting the Handset Ringer Volume/Pattern Ringer volumeIUU F23Selecting the Base Unit Ringer Volume/Pattern 22u223U Preparing the Answering System Selecting the Voice Guidance LanguageTo select to Slovakian, press To select to Czech, press Greeting Message Function item Time pTo set the greeting monitor Function pTime and Day Adjustment To check the time/dayPress repeatedly to set the day Minutes Greeting onlyRecording time Setting the Greeting Monitor Function Press Toll Saver When set to AutoCurrent setting, 1 or 2, is displayed on the base unit Selecting the Number of RingsTo select the receiver volume Making CallsI2345678 00 00Answering Calls To redial the last number dialedTo redial after confirming the numbers in redial memory To turn the handset ringer off temporarilySpeed Dialer Storing Phone Numbers in MemoryDialing a Stored Number To erase a stored numberIntercom Paging the base unit from the handsetPaging the handset from the base unit Handset locator Special Features How to Use the Pause FeatureSetting the pause timing To select 5 seconds, press To select 3 seconds, press PressSetting the Key Lock Using the Recall FeatureFor Rotary or Pulse Service Users To cancel the key lockSummary of Programmable Functions Setting the Password F5oF5o - - o 5o - - oSetting the Direct Call Mode To turn OFF the direct call modeDirect Call F42To turn OFF the call prohibition mode Call ProhibitionF4 Io F4 IO0To cancel the call restricted handsets To cancel the call restriction numbersCall Restriction I23456Selecting the Talk Mode Display Press G or F to select the desired settingF32U During a conversation, the display will be as followsAutomatic Route Selection Storing the Carrier Code/Area Codes To store the carrier codeTo store the area codes Other Programmable Settings F2 iF25 F26Clearing the Settings in Memory FunctionSetting the Unit to Answer Calls Automatic Answering OperationMonitoring incoming calls Press Answer on to turn on the answering systemFlash Memory Message Backup Listening to MessagesListening to only new messages Listening to all recorded messagesErasing Messages Recording a Memo MessageErasing a specific message Erasing all messagesRemote Operation from a Touch Tone Phone Summary of remote operationCanceling the remote operation To cancel, reprogram a new remote codeDisplay goes out Direct commands Direct Remote OperationRemote Operation from a Touch Tone Phone To continue the remote operationTurning on the answering system Skipping the greeting messageRemote Operation with the Handset Help menuMenu Recording your telephone conversation using the handset Continue your conversation When finished, press thenRemote Operation with the Handset During a conversation, press ThenFor Optional Multi-Unit Users Operating More than One HandsetOperating More than One Base Unit Registration F7 iRegistering a Handset in the Base Unit Selecting the Base Unit Access Automatic base unit accessSpecified base unit access I000Registration Canceling a Handset Canceling a base unitF70 i2 Selecting the Stand-by Mode Display Bell SelectionF3 i0 Iu2Bell Selection Selecting first handsetSelecting all handsets Enter the handset number you want to ringIntercom between the Handsets and the Base Unit Paging all the handsets from the base unit All pagingPaging a handset from the base unit Individual paging Page, then pressHandset When the unit rings, press to answer 00 00 0Intercom Intercom between Handsets Handset 1 Press I N T Enter the desired handset numberTransferring a call using the intercom Transferring a Call from One Handset to AnotherTransferring a call without the intercom Setting the Call Waiting Tone F24Intercom Conference Press Press G or F until F24 is displayed Press O KSelecting the battery type Battery replacementAfter replacement Replacing the BatteriesReplacing the Batteries Cordless Telephone Problem Remedy Before Requesting HelpProblem Remedy Before Requesting HelpDoes not function Answering System Problem Remedy Base unit, it suddenly stops Use indicator You cannot operate the answeringSystem at the base unit System from a touch tone phoneGeneral Problem Remedy Safety Instructions SafetyInstallations Environment PlacementLightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Obchodní oddélení Panasonic Czech Republic, s.r.o Krakovská 9, 110 00, Praha 1, Èeská republikaVýrobní závod PQQX12234ZA-UK WU1299NR0