Panasonic KX-TG7652AZ, KX-TG7653AZ operating instructions Installation, Wall mounting

Page 57

DECT repeater

indicator

Status		Meaning
Green		Signal strength of the
(On)		base unit is strong.

Amber		Signal strength of the
(On)		base unit is weak.

Red		Out of base unit range.
(On)

Off		R The unit is not being
		used.
		R The power is off.

Installation

1Connect the unit.

R Use only the supplied Panasonic AC adaptor PQLV219AL.

Hook

Press plug firmly. (220-240 V AC, 50/60 Hz)

R When the unit is turned on, the indicator and indicator light amber for about 2 seconds.

2Confirm that the indicator and

indicator light green. (The unit is ready for use.)

R If the indicators do not light green, re-position the unit in a place where the indicators light green.

Note:

R The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

R The AC adaptor should be connected to a vertically oriented or

floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.

R The unit can support a maximum of 3 handsets at a time.

Setting the repeater mode

This repeater is pre-registered to the base unit and the default setting of repeater mode is “On”. You do not need to change this setting for initial use.

1MMENUN #138

2MbN: Select the desired setting. a MSAVEN a MOFFN

Note:

R After turning the repeater mode on or off, is displayed on the handset momentarily. This is normal and the handset can be used once is displayed.

Wall mounting

Note:

R Make sure that the wall and the fixing method are strong enough to support the weight of the unit.

R Drive the screws (not supplied) into the wall.

Screws

37 mm

Wall mounting template

37 mm

57

Image 57

Contents Model shown is KX-TG7652 Before initial use, see Getting Started onUsing Bluetooth Devices Caller ID ServiceVoice mail Service for Landline IntroductionSeries Model compositionModel No Base unit Handset QuantitySupplied accessories Accessory informationAccessory item/Part number Quantity KX-TG7652 KX-TG7653 AC adaptor for base unit and chargerExpanding your phone system Additional/replacement accessoriesFor your safety Important safety instructions For best performance Power consumption Base unit Setting up ConnectionsCorrect Wrong Battery charging Battery installationConfirm Charging is displayed Charge indicator During a power failureIntelligent eco mode ControlsBase unit Handset Display/IndicatorsTalk Moffn Mrecalln Mcall WaitnUse Cell 1/CELL 2 indicators on the base unitBase unit display item Meaning Greeting onlyHeadset indicator on the base unit Initial settingsDate and time ExampleRegistering a cellular phone Link to cell featureTrademarks HandsetRing as cell mode Link to cell settingsSelecting which unit receives cellular calls MoffnConnecting/disconnecting the cellular phone manually Cellular line only mode If you do not use the landlineAuto connection to the cellular phone To turn onDeregistering Bluetooth devices Changing the Bluetooth PIN Personal Identification NumberCellular line selection Storing your area code for local callLink to Cell Making cellular calls Making landline callsMcelln Answering calls Useful features during a call Privacy mode Using the other line during a conversationWhile another unit is on a cellular call While another unit is on a landline callMbN Hold a Mselectn To make a 2nd call To answer a 2nd callMbN Hold a Mselectn Shared phonebook Adding entriesCell 1, Cell Groups Finding and calling from a phonebook entryEditing entries Chain dial Erasing entriesDisplay the menu tree and direct command code table Programmable settingsGreeting Settings Ring count*1 RingsCheck greeting Pre-recorded*1Device *4 Ringer volume BluetoothConnect *1 Add new Disconnect *1Alarm Once SettingsAdjustment *1, *10 Auto Manual Auto connect Min Cell areaRinger setting Ringer volume Main menu Initial settingHandset *3, *7 Ringer volume Night modePrivacy mode*1 Set tel line*3 Set recall 900 msRepeater mode*1 Registration Register handsetCondition is not good Newzealand = 600 msNight mode AlarmSpecial programming OffIncoming call barring Caller ID subscribers only Changing the handset nameMbN Caller barred a MclearnOperating additional units Registering a unitRegistering a handset to the base unit Additional handsetsDeregistering a handset Caller ID features Using Caller ID serviceCall waiting and Caller ID compatible for Australia Private caller The callerFor Caller ID Type II users Talking Caller IDMcall Waitn Phonebook name announcementCaller list Using a cellular lineRinger ID Viewing the caller list and calling backErasing all caller information Erasing selected caller informationStoring caller information to the phonebook To erase your area codeCopying phonebook from a cellular phone phonebook transfer Registering a headset to the base unit Operating a Bluetooth wireless headset using a landlineAdjusting your headset receiver volume Base unit Switching from the base unit to your headsetCall sharing between your headset and the handset While the handset is on a landline callTurning the answering system on/off Answering system for landlineMemory capacity including your greeting message Call screeningGreeting message Listening to messages using the base unitErasing all messages Listening to messages using the handsetOperating the answering system Calling back Caller ID subscribers onlyUsing the answering system remotely Remote access codeRemote commands Remote operationTurning on the answering system remotely Answering system settingsNumber of rings before the unit answers a call This will allow the voice mail to receive any messagesCaller’s recording time MMENUN#305 MbN Select the desired setting. a Msaven a MoffnMessage alert Selecting Greeting onlyVoice mail service for landline Storing the voice mail VM access numberListening to voice mail messages Voice mail Service for Landline Handset locator IntercomTransferring calls, conference calls Making an intercom callFor best performance Installation for Dect repeaterControls MprogramnWall mounting InstallationAC adaptor cord Wall mountingWall mounting template Charger25 mm Screws Hooks 25 mmBase no power Error messagesBusy Check tel line Error Failed Cause/solutionTroubleshooting General use Problem Cause/solutionInvalid Cannot hear a dial tone Programmable settings Problem Cause/solution Battery recharge Problem Cause/solutionMaking/answering calls, intercom Problem Can make and answer cellular calls but cannot hear a sound Caller ID/Talking Caller ID Problem Cause/solution Using Bluetooth devices Problem Cause/solution Noise is heard during a call on the headset Answering system Problem Cause/solution Deregister Dect repeater ProblemRe-register MlocatornRepeating tone is heard while talking using the handset Bluetooth PIN Problem Cause/solutionLiquid damage Problem Exchange Program Warranty for New ZealandIndex Index Page Page PNQX5357ZA TT0212MG0 For your future referenceSales Department