Cisco Systems ATA 188 CA0orCM0 and CA1orCM1, Voice Configuration Menu Access Codes, Examples

Page 69

Chapter 5 Parameters and Defaults

Account Information Parameters

Range

Maximum 51 characters for each parameter

Voice Configuration Menu Access Codes

46 and 47 for EPID0orSID0 and EPID1orSID1, respectively

CA0orCM0 and CA1orCM1

Description

CMx specifies the IP address (with an optional port number) or the URL of the primary or secondary Cisco CallManager to which the Cisco ATA should register. Use the CM0 parameter for the primary Cisco CallManager and the CM1 parameter for the secondary Cisco CallManager parameter. (CAx is not for SCCP.)

Note Use this parameter only if the default Cisco CallManager TFTP method is not desirable for configuring the Cisco CallManager IP address, in which case you must set the UseTftp parameter to 0.

If you specify a Cisco CallManager port, you must separate the port number from the host IP address with a colon (:).

Examples

Examples of CA0orCM0 values follow:

•192.168.1.2:2727

•ca.cisco.com.

Value Type

Alphanumeric string

Range

Maximum 31 characters

Default

0

Voice Configuration Menu Access Code

5 and 6, respectively

Related Parameters

•UseTFTP, page 5-4

•Domain, page 5-16

Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator’s Guide (SCCP)

	Ol-3141-01	5-9

Image 69

Contents Text Part Number OL-3141-01 Corporate HeadquartersCopyright 2003, Cisco Systems, Inc All rights reserved Iii N T E N T SWhat You Need DNS1IP DNS2IP Recommended Values Vii SyntaxViii Cisco ATA Style Conference Calling Procedure A-7Overview PrefaceAudience OrganizationConventions Preface Conventions Related Documentation Cisco IOS Telephony Service documentationObtaining Documentation Cisco.comDocumentation CD-ROM International Cisco web sites can be accessed from this URLOrdering Documentation Documentation FeedbackTechnical Assistance Center Obtaining Technical AssistanceCisco TAC Website XivCisco TAC Escalation Center Obtaining Additional Publications and InformationXvi A P T E R Cisco Analog Telephone Adaptor Overview4illustrates the architecture of an Sccp network Overview of the Skinny Client Control ProtocolLink LED Hardware OverviewFunction Button Software Features Sccp VersionVoice Codecs Supported Additional Supported Signaling Protocols Basic ServicesOther Supported Protocols Pre-call and Mid-call Services Fax ServicesPre-call Services Pre-call Services, Mid-call Services,Style and Related Services Procedure Reference Mid-call ServicesCisco ATA style services Cisco ATA Style, page A-6 Bellcore Style, page A-4Action Reference Installation and Configuration OverviewOL-3141-01 Installing the Cisco ATA Safety Recommendations Network RequirementsWhat the Cisco ATA Package Includes Installation Procedure 5V power adaptor Power cordWhat You Need Cisco ATA 186 Rear Panel Connections ProcedureInstalling the Cisco ATA Installation Procedure Power-Down Procedure Configuring the Cisco ATA for Sccp Default Boot Load Behavior Page Feature VLANSettingParameter and Bits Reference BitsHexadecimal format, this value is 0x01cc002b Action Reference Steps Needed to Configure the Cisco ATAConfiguring the Cisco ATA Using a Tftp Server Basic Configuration Steps in a Non-TFTP Server EnvironmentAction Configurable Features and Related Parameters Setting Up the Tftp Server with Cisco ATA SoftwareConfigurable Features Related Parameters Parameters Not Used for Sccp Creating a Cisco ATA Default Configuration FileSyntax Syntax of the cfgfmt program followsCreating a Configuration File for a Specific Cisco ATA You could change the values as followsSave your changes Cfgfmt -tmgcpptag.dat ata0a141e28323c.txt ata0a141e28323c Using atapname.exe Tool to Obtain MAC AddressCommand Example Using the EncryptKey Parameter and cfgfmt ToolCommand Output Syntax examplesUsing a Dhcp Server Using a Dhcp Server,Without Using a Dhcp Server, Procedure Other Dhcp Options You Can Set Without Using a Dhcp ServerUsing the Voice Configuration Menu Voice Configuration MenuVoice Menu Number Features Resetting the Cisco ATA to Factory Default Values Entering Alphanumeric ValuesKey Alphanumeric Characters Cisco ATA Web Configuration DNS1IP Resetting the Cisco ATA Using Cisco CallManager Confirmation box appears. Click OK Upgrading the Sccp Signaling ImageAdding the Cisco ATA to the Cisco CallManager Adding Cisco ATAs Manually Default value of NoneTime Click OKUsing the Cisco Bulk Administration Tool BAT Using Auto-Registration Parameters and Defaults CA0UID0 CA1UID0 Configuration Text File TemplateUser Interface UI Parameter UIPasswordSettings Parameters for Configuration Method and EncryptionRange Default Voice Configuration Menu Access Code UseTFTPMaximum 31 characters EncryptKey905 UseTFTP, Domain, 320 Network Parameters UseTFTP, TftpURL, DHCP, StaticIp, StaticRoute, StaticNetMask,StaticIp Voice Configuration Menu Access Code Related ParametersStaticRoute DHCP, StaticRoute, StaticNetMask,StaticNetMask Account Information ParametersEPID0orSID0 and EPID1orSID1 Value TypesVoice Configuration Menu Access Codes CA0orCM0 and CA1orCM1Examples Operating Parameters Sccp Mode ParameterUseMGCP Other ParametersInteger LBRCodecAudioMode PrfCodecConnectMode, page 5-13bit AudioMode, page 5-12bits 1 LBRCodec, ConnectMode,Bit Number Definition ConnectMode0x90000400 311CallerIdMethod To Use Pre-call and Mid-call Services316 0x00019e60916 DHCP,917 DomainNumTxFrames OpFlagsTftpURL, CA0orCM0 and CA1orCM1, VLANSetting TftpURL, DHCP, VLANSetting,See the VLANSetting section on Optional Feature Parameters SigTimerCallWaitTone, RingCadence Default Recommended ValuesList of Call-Progress Tone Parameters Call-Progress Tone ParametersTone Parameter Syntax Each tone is specified by nine integers, as followsHow to Calculate Scaling Factors Recommended ValuesUse the following formula to calculate the scaling factor a Specific Call-Progress Tone Parameter Information Default values for the nine-integer arrayDialTone 920BusyTone Cisco ATA plays the busy tone when the callee is busyReorderTone 921CallWaitTone RingbackTone923 924ConfirmTone NPrintf925 Extended IP addressUDPTOS, VLANSetting, Range DefaultTraceFlags MediaPortPage Using Fax Pass-through Mode Configuring and Debugging Fax ServicesThis setting translates to the following bitmap Configuring the Cisco ATA for Fax Pass-through modeAudioMode AudioMode, ConnectMode,Recommended Setting Configuring Cisco IOS Gateways to Enable Fax Pass-throughThis setting translates to the bitmap Enable Fax Pass-through Mode, Disable Fax Relay Feature,Enable Fax Pass-through Mode System Level commandsRun the following command Disable Fax Relay Feature Dial-Peer Level CommandsPerform the command Configuring the Cisco ATA for Fax Mode Using FAX ModeConfiguring the Cisco IOS Gateway for Fax Mode Debugging the Cisco ATA 186/188 Fax ServicesCommon Problems When Using IOS Gateways Run the commandUsing prserv for Diagnosing Fax Problems Prserv OverviewPrserv Overview, Analyzing prserv Output for Fax Sessions, Log event Description Analyzing prserv Output for Fax SessionsDecoding timestamp was set to timestamp2 That the first RTP packet that the Cisco ATA received wasDebugging FAX Pass-through Mode 100Terminating-Gateway Example Debugging FAX Mode Originating-Gateway ExamplePossible Reasons for Failure How to Use Using rtpcatch for Diagnosing Fax ProblemsRtpcatch Overview Major functionsExample of rtpcatch OptionsOutput CED tone Detected Explanation1032.116=2.213 Analyzing rtpcatch Output for Fax Sessions Fax relay mode Cisco fax relay modeAnalysis Both sides use G.711 for the entire fax sessionPossible Causes for Failure Using rtpcatch to Analyze Common Causes of FailurePossible Cause for Failure Cisco fax relay option is not disabled on the gatewayRtpcatch Limitations Example 6-10 Fax Pass-through Mode FailurePage Upgrading the Cisco ATA Signaling Image Procedure for Upgrading all Cisco ATAs at Once Upgrading the Signaling Image Via Cisco CallManagerUpgradecode Syntax ProcedureforUpgradingOneCiscoATAUpgradecode Definitions Running the ExecutablePreliminary Steps Upgrading the Signaling Image ManuallyRunning the Executable File Preliminary Steps, Running the Executable File,Upgrade Procedure Upgrade RequirementsSyntax DefinitionsUsing a Web Browser Confirming a Successful Signaling Image UpgradeUsing the telephone keypad, enter the following Using a Web Browser, Using the Voice Configuration Menu,Using the Voice Configuration Menu OL-3141-01 General Troubleshooting Tips TroubleshootingSymptoms and Actions Installation and Upgrade Issues Restarting the Cisco CallManager Debugging You should also have access to a sniffer or LAN analyzerRing Load per RJ-11 FXS Port Maximum Distance Frequently Asked QuestionsProcedure Contacting TAC How to Use Pre-call and Mid-call Services Procedures for Using Pre-call ServicesAccess Voicemail Activate Call-Forward-All Cancel Call-Forward-AllRedial Speed DialCall Pickup To use this feature, follow these stepsGroup Call Pickup MeetMe ConferenceBellcore Style Call Transfer Procedure Procedures for Using Mid-call ServicesBellcore Style Conference Call Procedure Bellcore StyleCisco VG248 Style Three-way Calling Procedure Cisco VG248 Call Transfer ProcedureCisco VG248 Style Cisco ATA Style Call Hold/Resume Procedure Cisco VG248 Conference Call ProcedureCisco ATA Style Call Transfer Procedure Cisco ATA StyleCisco ATA Style Conference Calling Procedure OL-3141-01 Voice Menu Codes Table B-1lists codes to return basic Cisco ATA informationVoice Menu Option Code Description DNS 2 IP 916 IP address of the primary DNS serverTable B-3 Cisco ATA Voice Menu Codes-Software Upgrade OL-3141-01 Cisco ATA Specifications Physical SpecificationsSpecification Environmental Specifications Electrical Specifications for Cisco ATAImmunity Specifications Description SpecificationSoftware Specifications Ringing CharacteristicsPhysical Interfaces Tip/ring interfaces for each RJ-11 FXS port SlicAppendix C Cisco ATA Specifications Software Specifications Sccp OL-3141-01 Sccp Call Flows Supported Sccp Message SetThis section describes basic call flows for the Cisco ATA Appendix D Sccp Call Flows Supported Sccp Message Set Cisco ATA-to-Cisco CallManager Call Flow Scenarios for Successful CallsATA Step Action DescriptionStep Station Call Info Description Cisco ATA-to-Cisco CallManager-to-Cisco ATAStep Station Call Info Description Step Station Call Info Description OL-3141-01 Performing a Cross-Protocol Upgrade Syntax of upgradecode ParameterProcess Upgradecode parameter value could be GL-1 GL-2 GL-3 GL-4 Signaling connection control part Messages can be part of Sgcp and Mgcp messagesGL-5 GL-6 Traffic Business-class services for Internet telephonyAllow you to define your own customized markup language GL-7GL-8 IN-1 EncryptKey CallerIdMethod ConnectMode DhcpEnabling use IN-2IN-3 IN-4 RTP frames RTP media port configurationIN-5 Safety recommendations Scaling factor calculationIN-6 IP encapsulation

Related manuals

Manual 228 pages 37.51 Kb

Manual 208 pages 28.48 Kb

Manual 64 pages 26.31 Kb

Manual 48 pages 9.1 Kb

Manual 208 pages 5.39 Kb

Manual 14 pages 13.53 Kb