Uniden BC125AT owner manual Look At The Display, Item Meaning

Page 30

2.If the scanner is new or has been reset, the default mode is Scan Hold with all banks enabled and Close Call Do- Not-Disturbactive. Otherwise, the scanner displays the last mode the scanner was in before it was powered down.

A Look At The Display

The display has indicators that show the scanner's current operating status. The display information helps you understand how your scanner operates.

Note: Not all of these icons may appear at the same time.

1

2

3

4

164	15	14	13	12
F H O L D		T L / O
C h a n n e l N a m e
C H 0 0 0 1		1 6 2. 5 2 5 0		↑
P	NFM	PRI+	C 2 5 4 . 1
B N K 1 2 3 4 5 6 7 8 9 0 C W X
	5	6	7	8

11

10

9

Item Meaning

1• Channel Name in Scan/Scan Hold mode.

•Custom/Service Search Bank Name.

•Quick Search in Quick Search mode.

•Close Call Hits in Scan/Scan Hold mode.

•Close Call in Close Call Only mode.

•WX Scan in Weather Scan mode.

•WX Alert Standby in WX Alert Standby mode.

30

Image 30

Contents BC125AT Owners Precautions Earphone WarningContents Programming Channels Weather Operation FCC Wants You To Know Scanning Legally Introduction Feature Highlights Direct Access lets you directly access any channelPage Page Frequency Range Step Mode Band Lower Upper USA Band PlanIncluded with Your Scanner Optional Accessories What is Scanning?Scanning Basics What is Searching? What is CTCSS/DCS?Understanding Scanning Conventional Scanning Simplex Operation Repeater OperationUnderstanding Banks Where To Learn MoreService Search Banks Channel Storage BanksSetting UP Your Scanner Connecting the AntennaConnecting an Earphone/Headphone Connecting an Extension SpeakerConnecting an Optional Antenna Adjusting the Belt Clip Powering the ScannerInstalling Non-Rechargeable Batteries Installing Rechargeable Ni-MH BatteriesCharging the Ni-MH Batteries USB Message Batt Meaning Scanner Type Cond About Your Scanner Getting to Know the ScannerPri Weather menuClr Scan FuncHold SrchPgm/E Turning On the ScannerPlay/Charge ProgrammingLook At The Display Item MeaningScan/Service Search/Custom Search/Close Call Only modeSetting Up Your Scanner Using the Scroll Control KnobAdjusting the Volume Adjusting the Squelch Setting the BacklightAdjusting the Contrast Setting the Charging Timer Display/Charge menuResetting the Scanner Using the Keypad LockSetting the Beep Tone All Memory Clear displaysProgramming Channels Programming Channel Text Tags Setting CTCSS/DCS for a Channel Setting Channel Modulation Channel menuSetting the Priority Channel Setting Channel Delay Deleting ChannelsScanning Stored Channels Clearing a BankPage Priority Scan Modes Manually Selecting a Channel Locking Out ChannelsUnlock all Channels in Banks Currently Enabled for Scan To Lock Out a Specific ChannelUnlocking Channels Service Search Mode Service Search Receive/Hold ModesCustom Search Mode Frequency MHz Step kHz Quick Search Mode Custom Search Receive/Hold ModesQuick Search Receive/Hold Modes Search Delay Search OptionsCTCSS/DCS Search Turn Scroll Control to CTCSS/DCS Search and press Pgm/EProgramming Custom Search Ranges Storing Found Search Frequencies Locking Out Search FrequenciesUnlocking Search Frequencies Using the Close Call Feature Close CallClose Call Only Mode Selecting Close Call ModesClose Call Menu Page Set Close Call Bands Close Call Alert Close Call Hits BankClose Call Delay Weather Operation Searching for a Weather BroadcastClose Call CTCSS/DCS Search Weather Alert Standby Technical Specifications Weather Alert PriorityTo exit Weather Alert Standby mode, press Scan Operating Temperature NFM 138.150 MHz 157.100 MHz Signal Noise Ratio nominal VHF Low Band 25.0050 MHz Rbrc Information References Ctcss FrequenciesDSC Codes BirdiesWarranty One Year Limited WarrantyPage Procedure for Obtaining Performance of Warranty