Uniden BC125AT owner manual USB Message Batt Meaning Scanner Type Cond

Page 25

Different status messages may display depending on the battery type and scanner status:

USB Message	Batt..	Meaning	Scanner
	Type		Cond..

Charging	Ni-MH	Scanner is charging.	Off
No Battery	None	NO batteries in	Off
		scanner.
Charge	Ni-MH	Unit is charged.	Off
Complete
Charge Off	Alk./Ni-	Scanner is not charg-	Off
	MH	ing (Battery selection
		switch is set to Alk.)
Battery Error	Ni-MH	Batteries cannot	Off
		be charged (dead
		battery).

Illegal Voltage	Ni-MH	USB external power	Off
		is out of range.

See also Setting the Charging Timer, page 35.

If the batteries are good, the scanner charges the batteries. and it operates normally. If the scanner cannot immediately determine if the batteries are good and can be charged, it checks them and displays the battery icon. If the scanner judges the batteries are good, the scanner starts charging and the battery icon disappears. If it cannot regard the batteries as good in 60 seconds, the scanner stops checking and the battery icon blinks.

25

Image 25

Contents BC125AT Owners Earphone Warning PrecautionsContents Programming Channels Weather Operation FCC Wants You To Know Scanning Legally Introduction Direct Access lets you directly access any channel Feature HighlightsPage Page Frequency Range USA Band Plan Step Mode Band Lower UpperIncluded with Your Scanner What is Scanning? Optional AccessoriesScanning Basics What is CTCSS/DCS? What is Searching?Understanding Scanning Conventional Scanning Repeater Operation Simplex OperationService Search Banks Where To Learn MoreUnderstanding Banks Channel Storage BanksConnecting the Antenna Setting UP Your ScannerConnecting an Extension Speaker Connecting an Earphone/HeadphoneConnecting an Optional Antenna Powering the Scanner Adjusting the Belt ClipInstalling Rechargeable Ni-MH Batteries Installing Non-Rechargeable BatteriesCharging the Ni-MH Batteries USB Message Batt Meaning Scanner Type Cond Getting to Know the Scanner About Your ScannerWeather menu PriClr Hold FuncScan SrchPlay/Charge Turning On the ScannerPgm/E ProgrammingItem Meaning Look At The DisplayOnly mode Scan/Service Search/Custom Search/Close CallUsing the Scroll Control Knob Setting Up Your ScannerAdjusting the Volume Setting the Backlight Adjusting the SquelchAdjusting the Contrast Display/Charge menu Setting the Charging TimerSetting the Beep Tone Using the Keypad LockResetting the Scanner All Memory Clear displaysProgramming Channels Programming Channel Text Tags Setting CTCSS/DCS for a Channel Channel menu Setting Channel ModulationSetting the Priority Channel Deleting Channels Setting Channel DelayClearing a Bank Scanning Stored ChannelsPage Priority Scan Modes Locking Out Channels Manually Selecting a ChannelTo Lock Out a Specific Channel Unlock all Channels in Banks Currently Enabled for ScanUnlocking Channels Service Search Receive/Hold Modes Service Search ModeCustom Search Mode Frequency MHz Step kHz Custom Search Receive/Hold Modes Quick Search ModeQuick Search Receive/Hold Modes Search Options Search DelayTurn Scroll Control to CTCSS/DCS Search and press Pgm/E CTCSS/DCS SearchProgramming Custom Search Ranges Locking Out Search Frequencies Storing Found Search FrequenciesUnlocking Search Frequencies Close Call Using the Close Call FeatureSelecting Close Call Modes Close Call Only ModeClose Call Menu Page Set Close Call Bands Close Call Hits Bank Close Call AlertClose Call Delay Searching for a Weather Broadcast Weather OperationClose Call CTCSS/DCS Search Weather Alert Standby Weather Alert Priority Technical SpecificationsTo exit Weather Alert Standby mode, press Scan Operating Temperature NFM 138.150 MHz 157.100 MHz Signal Noise Ratio nominal VHF Low Band 25.0050 MHz Rbrc Information Ctcss Frequencies ReferencesBirdies DSC CodesOne Year Limited Warranty WarrantyPage Procedure for Obtaining Performance of Warranty