Uniden BC125AT owner manual Adjusting the Contrast

Page 34

•Always On – Backlight is always on.

•On with Squelch - Backlight is on while squelch is open and until delay expires.

•On with Keypress - Backlight is on for 10 seconds after any key is pressed.

•Keypress+Squelch – Both above-mentioned "Squelch" and "Keypress."

•< Back - Return to previous menu.

4.Press Pgm/E (or press SCROLL CONTROL) to save and return to the previous menu. (Default = Always Off)

5.Press .. Clr to exit.

Notes: If the backlight is set to Always On when is pressed, the backlight is turned off and the backlight setting is then set to Always Off.

If the backlight is set to Always Off when is pressed, the backlight is turned on and the backlight setting is then set to Always On.

Adjusting the Contrast

This submenu of the Display/Charge menu controls the display’s contrast (how light or dark it appears) for different viewing conditions. There are 15 contrast settings. You see the contrast change as you scroll through the settings.

1.To adjust the contrast, press Func then ; the Display/ Charge menu displays

2.Scroll to Set Contrast and press Pgm/E.

3.Scroll to see the contrast settings.

34

Image 34

Contents BC125AT Owners Precautions Earphone WarningContents Programming Channels Weather Operation FCC Wants You To Know Scanning Legally Introduction Feature Highlights Direct Access lets you directly access any channelPage Page Frequency Range Step Mode Band Lower Upper USA Band PlanIncluded with Your Scanner What is Scanning? Optional AccessoriesScanning Basics What is CTCSS/DCS? What is Searching?Understanding Scanning Conventional Scanning Simplex Operation Repeater OperationUnderstanding Banks Where To Learn MoreService Search Banks Channel Storage BanksSetting UP Your Scanner Connecting the AntennaConnecting an Extension Speaker Connecting an Earphone/HeadphoneConnecting an Optional Antenna Adjusting the Belt Clip Powering the ScannerInstalling Non-Rechargeable Batteries Installing Rechargeable Ni-MH BatteriesCharging the Ni-MH Batteries USB Message Batt Meaning Scanner Type Cond About Your Scanner Getting to Know the ScannerWeather menu PriClr Scan FuncHold SrchPgm/E Turning On the ScannerPlay/Charge ProgrammingLook At The Display Item MeaningScan/Service Search/Custom Search/Close Call Only modeUsing the Scroll Control Knob Setting Up Your ScannerAdjusting the Volume Adjusting the Squelch Setting the BacklightAdjusting the Contrast Setting the Charging Timer Display/Charge menuResetting the Scanner Using the Keypad LockSetting the Beep Tone All Memory Clear displaysProgramming Channels Programming Channel Text Tags Setting CTCSS/DCS for a Channel Setting Channel Modulation Channel menuSetting the Priority Channel Setting Channel Delay Deleting ChannelsScanning Stored Channels Clearing a BankPage Priority Scan Modes Manually Selecting a Channel Locking Out ChannelsTo Lock Out a Specific Channel Unlock all Channels in Banks Currently Enabled for ScanUnlocking Channels Service Search Mode Service Search Receive/Hold ModesCustom Search Mode Frequency MHz Step kHz Quick Search Mode Custom Search Receive/Hold ModesQuick Search Receive/Hold Modes Search Delay Search OptionsTurn Scroll Control to CTCSS/DCS Search and press Pgm/E CTCSS/DCS SearchProgramming Custom Search Ranges Storing Found Search Frequencies Locking Out Search FrequenciesUnlocking Search Frequencies Using the Close Call Feature Close CallSelecting Close Call Modes Close Call Only ModeClose Call Menu Page Set Close Call Bands Close Call Alert Close Call Hits BankClose Call Delay Searching for a Weather Broadcast Weather OperationClose Call CTCSS/DCS Search Weather Alert Standby Weather Alert Priority Technical SpecificationsTo exit Weather Alert Standby mode, press Scan Operating Temperature NFM 138.150 MHz 157.100 MHz Signal Noise Ratio nominal VHF Low Band 25.0050 MHz Rbrc Information References Ctcss FrequenciesDSC Codes BirdiesWarranty One Year Limited WarrantyPage Procedure for Obtaining Performance of Warranty