Tyco LPE-200 manual Receiving an Emergency Call, Declaring an Emergency Call

Page 39

declared scanning will stop and restarts only after the emergency has been cleared.

Receiving an Emergency Call

When receiving an emergency call on the selected group and system, an alert beep is heard

and comes on. The message *RXEMER* flashes in the display on line two until the emergency condition is cleared.

Declaring an Emergency Call

To send an emergency call to selected system and group (or on an optionally preprogrammed group), proceed as follows:

1.Press and hold the red EMERGENCY button that is on top of the radio in front of the antenna for approximately one second (this time is programmable and therefore could be longer or shorter; check with the system administrator). The radio will transmit an emergency call request with the radio ID until an emergency channel assignment is received.

2.When the working channel assignment is received, the radio sounds a single beep indicating the radio has auto keyed (see Auto Key) and is ready for voice transmission. *TXEMER* flashes on line two in the display until the emergency is cleared.

3.Press PTT and speak into the microphone in a normal voice. and momentarily turns on.

39

Image 39
Contents EDACS/ProVoice LPE-200 Page Table of Contents Telephone Interconnect Digital Voice Operation Charging the Battery Pack Rechargeable Battery Pack Disposal Introduction User Interface LPE-200 Radio Scan Model Shown LPE-200 Radio System Model Shown Top, Back and Left Panel Views Buttons and Knobs System GROUP/ Channel Knob Power ON-OFF Volume KnobEMERGENCY/ Home Button Option Clear Monitor Button PUSH-TO Talk Button PTT Keypad Scan Model KeypadStandard Functions System Model Scan ModelButton and Keypad Reassignment Button and Key Assignments Display Radio Status Icons DisplayPage Page SYS Busy MessagesSysc on Rxemer Call Originate Error MessagesUniversal Device Connector UDC Alert TonesCall Denied Trunked Mode Only Call Queued Trunked Mode OnlyAutokey Trunked Mode Only System Busy Trunked Mode OnlyKey Press Alert Carrier Control TimerLow Battery Warning Low Battery Alert Transmit LockoutOperation Turning on the Radio System Selection SYSTEM/GROUP/CHANNEL SelectionPage Group or Channel Selection Page Page Receiving a Group Call Trunked Mode OperationPage Sending a Group Call Emergency Operation Conventional FailsoftDeclaring an Emergency Call Receiving an Emergency CallTurning Scan On and Off Scanning Trunked GroupsAdding Groups to a Scan List Scan Model Radios Page System Model Radios Deleting Groups from a Scan List Scan Model Radios Nuisance Delete Scanning Trunked Systems Wide Area System ScanningPriority System Scan When ProSound/ProScan Is Enabled When Wide Area System Scan Is EnabledProScan ProSoundMenu Selection Individual Calls Pre-Programmed Keypad KeyPage System Model Direct Dialing of Individual Calls System Model only Call Storage Lists Telephone Interconnect Calls Receiving a Telephone Interconnect Call Trunked Mode OnlyPage Direct Dialing of Phone Calls System Model only Dtmf Overdial / Conventional Mode Telephone Interconnect Scan Radio System Radio Programmable Entries Status Operation STATUS/MESSAGE OperationDynamic Regroup Operation Message OperationEmergency Operation Menu Macro KEY OperationPress M Press M Menu Item Information Feature Display Parameter Comment SettingGROUP/ Channel Digital Voice Operation Clear ModeDigital Mode Dtmf Private ModeSystem Encryption Key Displaying the Currently Used Cryptographic Key NumberPrivate Operation Receiving an Encrypted Call Group/Channel Encryption Key Key ZeroTransmitting an Encrypted Call Scanned Group Calls Yes Displays Portable DataData on Operation Data OFF OperationExiting Data Calls Scan Lockout ModeConventional Operation Data Lockout ModeSending a Call Receiving a CallAdding Channels to a Scan List Deleting Channels from a Scan List Turning Scan OFF Turning Scan onOperating Rules and Regulations Page Operating Tips Battery Packs Charging the Battery PackPage Installing the Battery Pack Rechargeable Battery Pack DisposalNickel Cadmium NiCd Battery Pack Disposal Nickel Metal Hydride NiMH Battery Pack DisposalRemoving the Battery Pack Installing and Removing Battery PackIntrinsically Safe Usage Battery Packs Accessories CCT GlossaryGroup. Trunked Mode only System Scan Programmed feature to scan monitor activity COM WarrantyBattery Warranty 100 OPERATOR’S Radio Setup101 Emergency NumbersCOM Wireless Systems