Tyco LPE-200 manual STATUS/MESSAGE Operation, Status Operation

Page 62

3.Enter the desired number. If necessary, a pause can be entered by pressing and holding 0-9, *, or #until an underscore appears in the

display (telephone interconnect only). The individual call list entries will accept up to 5 digits. The phone call list entries accept a combination of up to 31 digits and pauses.

4.Press and hold M until the display changes indicating that the number has been stored.

5.Repeat the steps above if the number stored in an entry location needs to be changed.

STATUS/MESSAGE OPERATION

Status operation permits the transmission of a pre-programmed status condition to the EDACS site. Message operation permits the transmission of a pre-programmed message text to an EDACS site.

STATUS OPERATION

To send a status condition, press the M key followed by < or > key to select the pre-

programmed status. STATUS and 0 through 9 pre- programmed status selections are available from the menu. If STATUS is selected you need to enter the number of the status message you intend to transmit. If no status has been programmed for the selected number key, the radio will display "NO ENTRY". A valid selection will permit the status text to appear in the display for a pre-programmed time. After the time-out expires or the M key has been

62

Image 62

Contents EDACS/ProVoice LPE-200 Page Table of Contents Telephone Interconnect Digital Voice Operation Charging the Battery Pack Rechargeable Battery Pack Disposal Introduction User Interface LPE-200 Radio Scan Model Shown LPE-200 Radio System Model Shown Top, Back and Left Panel Views System GROUP/ Channel Knob Power ON-OFF Volume Knob Buttons and KnobsEMERGENCY/ Home Button Option Clear Monitor Button PUSH-TO Talk Button PTT Keypad Keypad Scan ModelStandard Functions Scan Model System ModelButton and Keypad Reassignment Button and Key Assignments Display Display Radio Status IconsPage Page Messages SYS BusySysc on Rxemer Alert Tones Error MessagesUniversal Device Connector UDC Call OriginateSystem Busy Trunked Mode Only Call Queued Trunked Mode OnlyAutokey Trunked Mode Only Call Denied Trunked Mode OnlyLow Battery Alert Transmit Lockout Carrier Control TimerLow Battery Warning Key Press AlertOperation Turning on the Radio SYSTEM/GROUP/CHANNEL Selection System SelectionPage Group or Channel Selection Page Page Trunked Mode Operation Receiving a Group CallPage Sending a Group Call Conventional Failsoft Emergency OperationReceiving an Emergency Call Declaring an Emergency CallScanning Trunked Groups Turning Scan On and OffAdding Groups to a Scan List Scan Model Radios Page System Model Radios Deleting Groups from a Scan List Scan Model Radios Nuisance Delete Priority System Scan Scanning Trunked SystemsWide Area System Scanning When Wide Area System Scan Is Enabled When ProSound/ProScan Is EnabledProSound ProScanMenu Selection Pre-Programmed Keypad Key Individual CallsPage System Model Direct Dialing of Individual Calls System Model only Call Storage Lists Receiving a Telephone Interconnect Call Trunked Mode Only Telephone Interconnect CallsPage Direct Dialing of Phone Calls System Model only Dtmf Overdial / Conventional Mode Telephone Interconnect Scan Radio System Radio Programmable Entries STATUS/MESSAGE Operation Status OperationMessage Operation Dynamic Regroup OperationEmergency Operation Macro KEY Operation MenuPress M Press M Feature Display Parameter Comment Setting Menu Item InformationGROUP/ Channel Clear Mode Digital Voice OperationDigital Mode Private Mode DtmfDisplaying the Currently Used Cryptographic Key Number System Encryption KeyGroup/Channel Encryption Key Key Zero Private Operation Receiving an Encrypted CallTransmitting an Encrypted Call Scanned Group Calls Yes Portable Data DisplaysData OFF Operation Data on OperationScan Lockout Mode Exiting Data CallsData Lockout Mode Conventional OperationReceiving a Call Sending a CallAdding Channels to a Scan List Deleting Channels from a Scan List Turning Scan on Turning Scan OFFOperating Rules and Regulations Page Battery Packs Charging the Battery Pack Operating TipsPage Nickel Metal Hydride NiMH Battery Pack Disposal Rechargeable Battery Pack DisposalNickel Cadmium NiCd Battery Pack Disposal Installing the Battery PackInstalling and Removing Battery Pack Removing the Battery PackIntrinsically Safe Usage Battery Packs Accessories Glossary CCTGroup. Trunked Mode only System Scan Programmed feature to scan monitor activity Warranty COMBattery Warranty OPERATOR’S Radio Setup 100Emergency Numbers 101COM Wireless Systems