Tyco LPE-200 manual Adding Channels to a Scan List

Page 83

receiver or observe the display for the absence

of . If the Channel Busy Lockout feature is programmed for the selected channel, the radio will not transmit when the channel is busy.

3.Press and hold the PTT button. The radio will

display and a short beep sounds (if programmed) indicating that communication can begin.

4.Hold the radio approximately three inches from the mouth and speak in a normal voice into the microphone (located at upper left front corner).

5.Release the PTT button when the transmission is complete and listen for a reply.

The following procedures outline scan operations for conventional channels.

ADDING CHANNELS TO A SCAN LIST

1.With scan operation turned off select the desired channel to add to the selected conventional system channel scan list.

2.Press A (Scan) or 6 (System). The

current status will be displayed in column 10 of line three for a time-out period. Press A or

6 to add the channel to the scan list. is

displayed on the line. This sets the selected channel for non-priority scanning. One of the following messages may be momentarily displayed:

83

Image 83
Contents EDACS/ProVoice LPE-200 Page Table of Contents Telephone Interconnect Digital Voice Operation Charging the Battery Pack Rechargeable Battery Pack Disposal Introduction User Interface LPE-200 Radio Scan Model Shown LPE-200 Radio System Model Shown Top, Back and Left Panel Views Buttons and Knobs System GROUP/ Channel Knob Power ON-OFF Volume KnobEMERGENCY/ Home Button Option Clear Monitor Button PUSH-TO Talk Button PTT Keypad Scan Model KeypadStandard Functions System Model Scan ModelButton and Keypad Reassignment Button and Key Assignments Display Radio Status Icons DisplayPage Page SYS Busy MessagesSysc on Rxemer Call Originate Error MessagesUniversal Device Connector UDC Alert TonesCall Denied Trunked Mode Only Call Queued Trunked Mode OnlyAutokey Trunked Mode Only System Busy Trunked Mode OnlyKey Press Alert Carrier Control TimerLow Battery Warning Low Battery Alert Transmit LockoutOperation Turning on the Radio System Selection SYSTEM/GROUP/CHANNEL SelectionPage Group or Channel Selection Page Page Receiving a Group Call Trunked Mode OperationPage Sending a Group Call Emergency Operation Conventional FailsoftDeclaring an Emergency Call Receiving an Emergency CallTurning Scan On and Off Scanning Trunked GroupsAdding Groups to a Scan List Scan Model Radios Page System Model Radios Deleting Groups from a Scan List Scan Model Radios Nuisance Delete Priority System Scan Scanning Trunked SystemsWide Area System Scanning When ProSound/ProScan Is Enabled When Wide Area System Scan Is EnabledProScan ProSoundMenu Selection Individual Calls Pre-Programmed Keypad KeyPage System Model Direct Dialing of Individual Calls System Model only Call Storage Lists Telephone Interconnect Calls Receiving a Telephone Interconnect Call Trunked Mode OnlyPage Direct Dialing of Phone Calls System Model only Dtmf Overdial / Conventional Mode Telephone Interconnect Scan Radio System Radio Programmable Entries Status Operation STATUS/MESSAGE OperationDynamic Regroup Operation Message OperationEmergency Operation Menu Macro KEY OperationPress M Press M Menu Item Information Feature Display Parameter Comment SettingGROUP/ Channel Digital Voice Operation Clear ModeDigital Mode Dtmf Private ModeSystem Encryption Key Displaying the Currently Used Cryptographic Key NumberPrivate Operation Receiving an Encrypted Call Group/Channel Encryption Key Key ZeroTransmitting an Encrypted Call Scanned Group Calls Yes Displays Portable DataData on Operation Data OFF OperationExiting Data Calls Scan Lockout ModeConventional Operation Data Lockout ModeSending a Call Receiving a CallAdding Channels to a Scan List Deleting Channels from a Scan List Turning Scan OFF Turning Scan onOperating Rules and Regulations Page Operating Tips Battery Packs Charging the Battery PackPage Installing the Battery Pack Rechargeable Battery Pack DisposalNickel Cadmium NiCd Battery Pack Disposal Nickel Metal Hydride NiMH Battery Pack DisposalRemoving the Battery Pack Installing and Removing Battery PackIntrinsically Safe Usage Battery Packs Accessories CCT GlossaryGroup. Trunked Mode only System Scan Programmed feature to scan monitor activity COM WarrantyBattery Warranty 100 OPERATOR’S Radio Setup101 Emergency NumbersCOM Wireless Systems