Friedrich UE12, UE10, UE08 manual Installation, HOW to Install, Procedure Brand

Page 12

Parts and Installation

INSTALLATION

CAUTION

Installing the FRIEDRICH USC sleeve ensures optional performances of the unit.

If you decide to keep the existing wall sleeve, you have to redirect the louvers at the back of the wall sleeve. Refer to FIG. 8 on p14. The use of pliers is recommended. If you DO NOT redirect, you run the risk of poor performance or premature product failure. This is not covered under the terms of the FRIEDRICH warranty.

•Pick a location which will allow the conditioned air to blow into the area you want. Good installation with special attention to the proper position of the unit will lessen the chance that service will be needed.

ITEMS IN INSTALLATION HARDWARE

You may not need all parts in the kit. Discard unused parts

ITEM

DIMENSIONS(inches)

Qty.

Plastic grille

263/4 x 161/2

1

Horizontal Insulation Strips

13/8 x 5/8 x 273/16

1

13/8 x 13/8 x 273/16

1

 

Around Insulation Strips

13/8 x 3/4 x 611/2

1

13/8 x 13/8 x 611/2

1

 

Support Block

13/4 x 13/8 x 45/16

2

Baffle

14 x 41/2 x 1/8

1

Shim

13 x 1 x 3/4

2

Trim Frame

 

2

Washer Screw

 

4

Nuts(Plastic)

 

4

Grille Rear

 

1

HOW TO INSTALL

1 Before installing the unit, identify the existing wall sleeve from the list below.

Brand

Wall Sleeve Dimensions (inches)

Width

Height

Depth

 

White-Westinghouse

 

 

16, 17-1/2

Frigidaire

25-1/2

15-1/4

Carrier (52F series)

 

 

or 22

 

 

 

General Electric

26

15-5/8

16-7/8

/Hotpoint

 

 

 

Whirlpool

25-7/8

16-1/2

17-1/8

or 23

 

 

 

Fedders/Emerson

27

16-3/4

16-3/4

Friedrich WSC

or 19-3/4

 

 

FRIEDRICH USC

25-7/8

15-17/32

16-23/32

Emerson/Fedders

26-3/4

15-3/4

15

Carrier (51S Series)

25-3/4

16-7/8

18-5/8

NOTE: All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner.

2 Removesleeve. old air conditioner from existing wall

Clean the interior of an existing sleeve.

3 (Do not disturb seals or gaskets.)

4 Wall sleeve must be securely fastened in wall before installing the air conditioner. Use the nails or screws through sleeve into wall, if needed. Repaint sleeve if needed.

5 Prepare the wall sleeve for installation of the unit. If you plan to use your existing wall sleeve, and it is not FRIEDRICH, use procedure B or C below.

Procedure

Brand

Depth(inches)

A(page 13)

FRIEDRICH USC

16-23/32

 

White-Westinghouse

16, 17-1/2

 

Frigidaire Carrier

 

or 22

B

(52F series)

 

General Electric

 

(pages 14~15)

16-7/8

 

/Hotpoint

 

 

Whirlpool

17-1/8 or 23

 

Carrier (51S series)

18-5/8

C

Fedders/Emerson

16-3/4

Friedrich WSC

or 19-3/4

(pages 16~17)

Emerson/Fedders

15

 

 

 

6 Install new unit into wall sleeve.

CAUTION: When installation is completed, replacement unit MUST have a rearward slope as shown. To achieve 1/4" slope, remove the backing from the 11-13/16" shim strips and attach them as shown below in Fig. 3. Place the higher portion of shim to the front of the rib on base of wall sleeve.

1" high

3/4" High

 

 

UNIT

Wall Sleeve

Shim

FRONT

 

 

 

6"

1/4"

 

6"

 

SHIM PLACEMENT

UNIT INSTALLATION

 

 

FIG. 3

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation & Operation Guide Thru-the-Wall Series How to Attach Front Grille 13-17Safety Precautions Meanings of symbols used in this manual are as shown belowIt will cause electric shock or fire due to heat generation They are sharp and may cause an injury This could harm the pets or plantsUse Wall Receptacle Power Supply Electrical DataElectrical Data USE of Extension CordsOperating Instructions Controls Cooling Only ModelsFor Normal Cooling For Maximum CoolingControls Cooling & Heating Off Turns the air conditioner off Fan OnlyLow fan speed operation without cooling/heating Ventilation Control Air DirectionHorizontal AIR-DIRECTION Control Vertical AIR-DIRECTION ControlCare and Maintenance Air Filter CleaningHow to Attach Front Grille to Cabinet Parts PartsInstallation Installation HOW to InstallProcedure Brand Procedure a Make sure air conditioner does not fall during removalProcedure B Top ViewWall sleeve inches Procedure a WallProcedure C Remove the backing from the HorizontalIf the depth of your existing sleeve is less than Or equal to 18, skip to . Otherwise, cutRemove the backing from the 13 shim strips Attach them as shown below in FigHigher portion of shim is to be placed Front of the rib on the base of wall sleeveBefore you call for service Trouble Shooting TipsNormal Operation Abnormal OperationTHRU-THE-WALL Limited Warranty Friedrich Air Conditioning-Co Box San Antonio, TX 210Memo Numéro DE Modèle Numéro DE Série Date Dachat Installation ’installation ProcédureComment procéder à Mesures de sécuritéMesures de Sécurité Cela pourrait nuire à votre santéCela pourrait nuire à la santé de l’animal ou de la plante Cela pourrait provoquer une décharge électriquePropriétés Électriques Propriétés électriquesUtilisation DE Rallonges Electriques Climatiseurs 208/230VPropos des commandes du climatiseur Contrôles seulement sur les modèles de refroidissementPour UN Refroidissement Normal Pour UN Refroidissement MaximumContrôles Refroidissement & chauffage Contrôle de la ventilation Direction de l’airContrôle DE LA Direction Horizontale Contrôle DE LA Direction VerticaleComment installer le panneau avant sur le caisson EntretienNettoyage du filtre à air Ouvrez la grille d’arrivée d’airDifférentes parties Les différentes parties’installation De l’installation’appareil ’appareil pendant une période prolongéeMarque Mur Encadrement2 eaVue d’en haut Placez la grille en plastiqueSuite DE LA Procedure B Insérez le déflecteur dans la rainure des renfortsMur Procé Dure C Vue den hautExistant pouces Pouces Suite DE LA Procedure C Caisson muralAvant de faire appel à un dépanneur… Astuces de dépannageFonctionnement normal Fonctionnement anormalPremiè re Anné e De la deuxiè me à la cinquiè me anné eNota Número DE Modelo Número DE Serie Fecha DE Compra Precauciones de Seguridad Medidas de seguridad Por el fabricante o un centro deServicio autorizado Esto podría dañar su saludSon afiladas y pueden causar lesiones Podría causar fuego o daños a la carcasaEléctrica Objetos de arteDatos eléctricos Datos eléctricosUSO DE Alargaderas Unidades DE 208/230 VoltiosInstrucciones de funcionamiento Controles modelos de sólo refrigeraciónRefrigeració N Normal Refrigeració N MÁ XimaControles refrigeración y calefacción Off El aire acondicionado se apaga Fan OnlyRefrigerar / calentar Funcionamiento del ventilador a baja velocidad sinControl de ventilación Dirección del aireControl Horizontal DE LA Direcció N DEL Aire Control Vertical DE LA Direcció N DEL AireCuidado y mantenimiento Limpieza del filtro de aireAcoplamiento de la rejilla frontal a la carcasa Piezas PiezasRejilla DE Entrada Entrada de aire Incluye rejilla expandida posterior de aluminioInstalación Requisitos DE Instalació NInstalació N MarcaProcedimiento a 8 x 5/ 8 x 27 3/ 16 y acople la cinta a la parteProcedimiento B Visión superiorColocación de la rejilla plásticaFIG Procedimiento B Continuado ParedMonte el ajuste según lo descrito en el paso Procedimiento aProcedimiento C Mirando desde arriba13/8 x 13/8 x 27 3/16 y acople la cinta a la parte Instale la parrilla de plásticoProcedimiento C Continuado Del soporte de la paredAntes de solicitar asistencia técnica Consejos sobre la solución de averíasFuncionamiento normal Funcionamiento anormalSerie Para Pared Garantía Limitada Friedrich AIR Conditioning CO. INC
Related manuals
Manual 23 pages 51.2 Kb

UE08, UE10, UE12 specifications

Friedrich is a renowned name in the air conditioning industry, known for its commitment to quality and innovation. Among their popular models are the UE12, UE08, and UE10 air conditioning units, each designed to cater to different needs while maintaining high energy efficiency and performance standards.

The Friedrich UE12 is a robust unit that offers powerful cooling capabilities, making it suitable for medium to large rooms. With a cooling power of approximately 12,000 BTU, it effectively cools spaces without requiring excessive energy consumption. This model features a programmable thermostat, enabling users to set desired temperatures and automatically adjusting to maintain them. The UE12 also includes a remote control, allowing for easy adjustments from across the room. Its built-in dehumidifier function is an added bonus, keeping indoor humidity levels in check, which improves overall comfort and air quality.

The Friedrich UE08, with its 8,000 BTU cooling capacity, is perfect for smaller rooms or individual spaces. It strikes a balance between power and energy efficiency, making it ideal for those looking to cool a bedroom, home office, or den without incurring high electricity bills. The model features an easy-to-use control panel and a remote control, giving users flexibility in operating the unit from anywhere in the room. Additionally, its sleek design blends well with various interior styles, making it both a practical and aesthetically pleasing option.

Lastly, the Friedrich UE10 provides a cooling capacity of 10,000 BTU and is a versatile option suitable for medium-sized rooms. This model also includes advanced features like a multi-speed fan, allowing users to customize airflow according to their preferences. The UE10 is equipped with a programmable timer, allowing users to set it to turn on or off at specific times, thus maximizing energy efficiency. The unit's whisper-quiet operation and energy-saving capabilities position it as an excellent choice for those who value tranquility in their indoor environment.

Overall, the Friedrich UE series air conditioning units demonstrate a commitment to quality, efficiency, and user-friendly features. From the powerful cooling of the UE12 to the compact design of the UE08, these units cater to diverse cooling needs while ensuring optimal performance.
Top Page Image Contents