Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
TROUBLESHOOTING & REPAIR | ||
|
Observe Safety Guidelines detailed in the beginning of this manual.
PROBLEMS |
| POSSIBLE AREAS OF |
| RECOMMENDED |
| |||
(SYMPTOMS) |
| MISADJUSTMENT(S) |
| COURSE OF ACTION |
| |||
|
|
|
|
|
|
|
|
|
|
| OUTPUT PROBLEMS |
|
|
|
|
|
|
Inconsistent wire feeding or wire not | 1. | The gun cable is kinked. | 1. | Keep the gun as straight as | ||||
feeding but the drive rolls are turn- | 2. | The wire is jammed in the gun |
| possible. | Avoid sharp corners | |||
ing. |
| or bends in the gun cable. | ||||||
| cable. |
| ||||||
|
|
|
|
|
|
|
| |
| 3. | The gun liner is dirty or worn. | 2. Remove the gun and clear the | |||||
|
| jam. |
|
|
|
| ||
|
|
|
|
|
|
|
| |
| 4. | The electrode is rusty or dirty. | 3. Clear liner with pressurized air | |||||
|
|
| ||||||
| 5. | The gun tip is worn or has splat- |
| (40 PSI) or less. Change liner if | ||||
|
| ter. |
| worn. |
|
|
|
|
| 6. | Improper gun liner, tip, drive | 4. | Use only clean electrode. | Use | |||
|
| rolls, or wire guides. |
| only quality electrode, like | ||||
| 7. | Incorrect pressure on the wire |
| or | from | the Lincoln | ||
|
| Electric. |
|
|
|
| ||
|
| drive rolls. |
|
|
|
|
| |
|
|
|
|
|
|
|
| |
| 8. | Spindle brake to tight. | 5. Replace the contact tip. |
| ||||
|
|
|
|
|
|
| ||
| 9. | Worn drive rolls. | 6. Verify the proper parts are | |||||
|
| installed. |
|
|
|
| ||
|
|
|
|
|
|
|
| |
|
|
| 7. Adjust the tension arm per the | |||||
|
|
|
| manual. Most electrodes feed | ||||
|
|
|
| well with the tension at around | ||||
|
|
|
| “3”. |
|
|
|
|
|
|
| 8. Verify the | spool | moves | with | ||
|
|
|
| minimal effort. |
|
|
| |
|
|
| 9. Replace the drive rolls if need- | |||||
|
|
|
| ed. |
|
|
|
|
|
|
|
|
| ||||
Wire feed speed consistently oper- | 1. | The jumper lead for normal | 1. | Properly connect the jumper. | ||||
ates at the wrong value. The speed |
| speed / extra torque is connect- | 2. Install the proper pinion fear in | |||||
changes when the control knob is |
| ed improperly. | ||||||
|
| the wire drive unit. |
| |||||
adjusted. |
|
|
|
| ||||
2. | The wrong gear is installed in |
|
|
|
|
|
| |
| 3. | Replace | the | motor/gearbox | ||||
|
| the wire drive unit. | ||||||
|
|
| assembly. |
|
|
|
| |
|
|
|
|
|
|
|
| |
| 3. | The motor brushes are worn. |
|
|
|
|
|
|
|
|
|
|
|
| |||
This wire feeds but cannot be con- | 1. | The tachometer is connected | 1. | Verify that tachometer | leads | |||
trolled with the wire speed pot. |
| improperly. |
| are properly connected. |
| |||
| 2. | The tachometer has failed. | 2. | Perform | the | MOTOR | AND | |
|
|
|
| TACHOMETER TEST. Replace | ||||
|
|
|
| the tachometer if necessary. | ||||
|
|
| 3. | Possible control board problem. | ||||
|
|
|
|
|
|
|
|
|
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact the Lincoln Electric Service Department for technical troubleshooting assistance before you proceed. Call