Lincoln Electric IM10066 manual PRE-OPERATION Engine and COM- Pressor Service, Oil, Fuel CAP

Page 14

A-4

INSTALLATION

A-4

 

 

 

PRE-OPERATION ENGINE AND COM- PRESSOR SERVICE

READ the engine and compressor operating and maintenance instructions supplied with this machine.

WARNING

•Keep hands away from the engine muffler or HOT engine parts.

•Stop engine and allow to cool before fuelling.

•Do not smoke when fuelling.

•Fill fuel tank at a moderate rate and do not over- fill.

•Wipe up spilled fuel and allow fumes to clear before starting engine.

•Keep sparks and flame away from tank.

------------------------------------------------------------------------

OIL

The AIR VANTAGE® 500 (AU) is shipped with the engine crankcase filled with high quality SAE 10W-30 oil (API class CD or better). Check the engine and compressor oil levels before starting the engine. If it is not up to the full mark on the dip stick, add oil as required. Check the oil level every four hours of run- ning time during the first 35 running hours. Refer to the engine and compressor Operator’s Manuals for specific oil recommendations and break-in informa- tion. The oil change interval is dependent on the quali- ty of the oil and the operating environment. Refer to the engine and compressor Operator’s Manuals for the proper service and maintenance intervals.

FUEL USE DIESEL FUEL ONLY

•Fill the fuel tank with clean, fresh diesel fuel. The capacity of the fuel tank is approximately 25 gallons (95 liters). See engine Operator’s Manual for specif- ic fuel recommendations. Running out of fuel may require bleeding the fuel injection pump.

NOTE: Before starting the engine, open the fuel shut- off valve (pointer to be in line with hose).

FUEL CAP

Remove the plastic cap covering from the Fuel Tank Filler neck and install the Fuel Cap.

ENGINE COOLANT

WARNING

HOT COOLANT can burn skin.

•Do not remove cap if radiator is hot.

------------------------------------------------------------------------

The welder is shipped with the engine and radiator filled with a 50% mixture of ethylene glycol and water. See the MAINTENANCE section and the engine Operator’s Manual for more information on coolant.

bATTERY CONNECTION

WARNING

GASES FROM bATTERY can explode.

•Keep sparks, flame and cigarettes away from battery.

To prevent EXPLOSION when:

•INSTALLING A NEW bATTERY — disconnect negative cable from old battery first and connect to new battery last.

•CONNECTING A bATTERY CHARGER — remove battery from welder by disconnecting negative cable first, then positive cable and battery clamp. When reinstalling, connect negative cable last. Keep well ventilated.

•USING A bOOSTER — connect positive lead to battery first then connect negative lead to nega- tive battery lead at engine foot.

bATTERY ACID can burn eyes and skin.

•Wear gloves and eye protection and be careful when working near battery.

•Follow instructions printed on battery.

------------------------------------------------------------------------

IMPORTANT: To prevent ELECTRICAL DAMAGE WHEN:

a)Installing new batteries.

b)Using a booster.

Use correct polarity — Negative Ground.

AIR VANTAGE® 500 (AU)

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Safety Depends on You 11656Safety California Proposition 65 WarningsIiSAFETY IiiSAFETY IiiIvSAFETY Précautions DE SûretéElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply On-Line Product Registration ViiPlease Examine Carton and Equipment For Damage Immediately TAbLE of Contents TAbLE of Contents Open Circuit Voltage InstallationDuty Cycle Welding Output Volts at Rated Amps Height Width DepthStoring Safety PrecautionsLocation and Ventilation StackingHigh Altitude Operation High Temperature OperationLifting TowingFuel USE Diesel Fuel only PRE-OPERATION Engine and COM- Pressor ServiceOIL Fuel CAPSpark Arrestor AIR Cleaner Inlet HoodMuffler Outlet Pipe Welding TerminalsSTANDbY Power Connections Remote ControlAuxiliary Power Receptacles Across The-Arc Model Connection of Lincoln ELEC- Tric Wire FeedersConnection of LN-15 to the AIR Vantage 500 AU Control Cable ModelConnection of the LN-25 to the AIR Vantage 500 AU Shut off welder before making any electrical con- nectionsOperation General DescriptionControls and Settings ENGINE PROTECTION Idler SwitchOIL Pressure Gauge Output ControlWire Feeder Voltmeter Switch WELD MODE SELECTOR SWITCHWelding Terminals Switch PIN ConnectorAIR Compressor Controls 26 Thru VRD Operation Indicator Welding Power SourcesSafety What are VRD and Rocv DEVICES?Typical Fuel Consumption Starting TechniqueBREAK-IN Period Table b.1 Cummins b3.3 Engine Fuel ConsumptionTouch Start TIG Mode Stick Welding ModeCC-STICK Mode Welder OperationTable b.3 Typical Current Ranges Wire WELDING-CVARC Gouging Paralleling Auxiliary Power OperationSimultaneous Welding and AUXIL- Iary Power Loads PlusTIG Options AccessoriesOptional Field Installed Accessories K2641-2 Four Wheeled STEERAbLE Yard TrailerMaintenance Compressor MaintenanceService Instructions Single- and Two-StageEngine Air CleanersPreventing Electrical Damage Fuel FiltersCooling System Storage CleaningWelder / Generator MAINTE- Nance Nameplates / Warning Decals MAIN- TenanceTROUbLESHOOTING POSSIbLE PRObLEMSSymptoms Cause Recommended Course of ActionTROUbLESHOOTING Faulty receptacle Wiring Diagram Diagrams Engine Welders / K867 / K775 / LN-7 Connection Diagram To Work Electrode Cable To Wire Feed UnitDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Dimension Print AIR Vantage 500 AU Precaucion Warnung
Top Page Image Contents