Lincoln Electric IM10066 manual Faulty receptacle

Page 37

E-4	TROUbLESHOOTING	E-4

	Observe all Safety Guidelines detailed throughout this manual

PRObLEMS

(SYMPTOMS)

POSSIbLE

CAUSE

RECOMMENDED

COURSE OF ACTION

Engine goes to low idle but does not 1. Faulty Peripheral PCB, Pull

stay at low idle.Coil/Battery PCB or Weld Control PCB.

No welding output or auxiliary output. 1.		Broken lead in rotor circuit.
	2.	Faulty field diode module.
	3.	Faulty Weld Control PCB.
	4.	Faulty rotor.

Welder has some/ no output and no 1.		Faulty remote kit.
control. Auxiliary output OK	2.	Faulty output control potentiome-
		ter.
	3.	Faulty output control wiring.
	4.	Faulty Weld Control PCB, Pull
		Coil/Battery PCB or Chopper PCB.

No welding output. Auxiliary output 1.		WELDING TERMINALS switch in
OK.		wrong position, be sure switch is
		in WELDING TERMINALS
		ALWAYS ON position.
	2.	Faulty Weld Control PCB, Pull
		Coil/Battery PCB or Chopper PCB.
			If all recommended possible	areas
			If all recommended possible	areas
No auxiliary power.	1.	RCD may have tripped.	of misadjustment have	been
	2.	Open breakers may need to be checked and the problem persists,
		reset.	Contact your local Lincoln
	3.	Faulty receptacle.	Authorized Field Service Facility.
	4.	Faulty auxiliary circuit wiring.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

AIR VANTAGE® 500 (AU)

Image 37

Contents 11656 Safety Depends on YouCalifornia Proposition 65 Warnings SafetyIiSAFETY Iii IiiSAFETYPrécautions DE Sûreté IvSAFETYElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Please Examine Carton and Equipment For Damage Immediately ViiOn-Line Product Registration TAbLE of Contents TAbLE of Contents Duty Cycle Welding Output Volts at Rated Amps InstallationOpen Circuit Voltage Height Width DepthLocation and Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingOIL PRE-OPERATION Engine and COM- Pressor ServiceFuel USE Diesel Fuel only Fuel CAPMuffler Outlet Pipe AIR Cleaner Inlet HoodSpark Arrestor Welding TerminalsAuxiliary Power Receptacles Remote ControlSTANDbY Power Connections Connection of LN-15 to the AIR Vantage 500 AU Connection of Lincoln ELEC- Tric Wire FeedersAcross The-Arc Model Control Cable ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the AIR Vantage 500 AUGeneral Description OperationControls and Settings OIL Pressure Gauge Idler SwitchENGINE PROTECTION Output ControlWelding Terminals Switch WELD MODE SELECTOR SWITCHWire Feeder Voltmeter Switch PIN ConnectorAIR Compressor Controls 26 Thru Safety Welding Power SourcesVRD Operation Indicator What are VRD and Rocv DEVICES?BREAK-IN Period Starting TechniqueTypical Fuel Consumption Table b.1 Cummins b3.3 Engine Fuel ConsumptionCC-STICK Mode Stick Welding ModeTouch Start TIG Mode Welder OperationARC Gouging Wire WELDING-CVTable b.3 Typical Current Ranges Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationParalleling PlusOptional Field Installed Accessories AccessoriesTIG Options K2641-2 Four Wheeled STEERAbLE Yard TrailerCompressor Maintenance MaintenanceSingle- and Two-StageEngine Air Cleaners Service InstructionsCooling System Fuel FiltersPreventing Electrical Damage Welder / Generator MAINTE- Nance CleaningStorage Nameplates / Warning Decals MAIN- TenanceTROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionTROUbLESHOOTING Faulty receptacle Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Dimension Print AIR Vantage 500 AU Precaucion Warnung