Lincoln Electric IM10066 manual Starting Technique, BREAK-IN Period, Typical Fuel Consumption

Page 25

b-7

OPERATION

b-7

 

 

 

Unlike other VRD’s Lincoln uses micro processor con- trol to monitor and establish the arc without the stick- ing and shorting of the electrode to the job as seen in many other VRD installations. Due to the requirement of the resistance in the circuit to be low, for a VRD to operate, a good metal-to-metal contact must be made between the metal core of the electrode and the job.

Any damaged connection anywhere in the output cir- cuit may limit the operation of the VRD. This includes a good connection of the work return clamp and the job. The work return clamp should be connected close as practical to where the welding will be performed.

Some electrodes form a cone at the end of the elec- trode after the welding arc has been broken, particu- larly iron powder and low hydrogen electrodes.

This cone will need to be broken off in order to have the metal core of the electrode to make contact.

STARTING TECHNIQUE

The starting technique that has successfully overcome the problem is the push, twist, and peel technique. This technique requires the operator to push the elec- trode into the joint and twist.

The Push and Twist breaks off the cone and allows the metal electrode to make contact.

The peel and lift of the electrode establishes a con- trolled start to the welding arc. Normal welding tech- nique for the application is then used.

bREAK-IN PERIOD

The engine used to supply power for your welder is a heavy duty, industrial engine. It is designed and built for rugged use. It is very normal for any engine to use small quantities of oil until the break-in is accom- plished. Check the oil level twice a day during the break-in period. In general this takes 50 to 100 hours of operation.

IMPORTANT

IN ORDER TO ACCOMPLISH THIS bREAK-IN, THE UNIT SHOULD bE SUbJECTED TO HEAVY LOADS, WITHIN THE RATING OF THE MACHINE. AVOID LONG IDLE RUNNING PERIODS.

TYPICAL FUEL CONSUMPTION

Refer to Table B.1 for typical fuel consumption of the AIR VANTAGE® 500 (AU) Engine for various operat- ing settings.

Table b.1

Cummins b3.3 Engine Fuel Consumption

 

 

Cummins B3.3

Running Time for

 

 

 

56HP(42Kw)

25GAL.(94.6L)

 

 

 

@1800 RPM

(Hours)

 

 

Low Idle -

.59 Gal./hour

42.4

 

 

no load 1425 RPM

(2.2 L/hour)

 

 

 

High Idle -

.87 Gal./hour

28.7

 

 

no load 1900 RPM

(3.3 L/hour)

 

 

 

DC CC Weld

2.10 Gal./hour

11.9

 

 

Output 500

(7.9 L/hour)

 

 

 

Amps @ 40 Volts

 

 

 

 

Auxiliary Power

1.44 Gal./hour

17.4

 

 

12,000 VA

(5.5 L/hour)

 

 

 

Air Compressor

1.29 Gal./hour

19.4

 

 

60 CFM @ 100 PSI

(4.9 L/hour)

 

 

 

Air Compressor

 

 

 

 

60 CFM @ 100 PSI

2.46 Gal./hour

10.2

 

 

and DC, CC Weld

(9.3 L/hour)

 

 

 

Output 500 Amps

 

 

 

 

@40 Volts

 

 

 

 

Air Compressor

 

 

 

 

60 CFM @ 100 PSI

1.94 Gal./hour

12.9

 

 

and Auxiliary Power

(7.3 L/hour)

 

 

 

12,000 VA

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: This data is for reference only. Fuel consumption is approximate and can be influenced by many factors, includ- ing engine maintenance, environmental conditions and fuel quality.

AIR VANTAGE® 500 (AU)

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 11656 Safety Depends on YouCalifornia Proposition 65 Warnings SafetyIiSAFETY Iii IiiSAFETYPrécautions DE Sûreté IvSAFETYElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Please Examine Carton and Equipment For Damage Immediately ViiOn-Line Product Registration TAbLE of Contents TAbLE of Contents Duty Cycle Welding Output Volts at Rated Amps InstallationOpen Circuit Voltage Height Width DepthLocation and Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingOIL PRE-OPERATION Engine and COM- Pressor ServiceFuel USE Diesel Fuel only Fuel CAPMuffler Outlet Pipe AIR Cleaner Inlet HoodSpark Arrestor Welding TerminalsAuxiliary Power Receptacles Remote ControlSTANDbY Power Connections Connection of LN-15 to the AIR Vantage 500 AU Connection of Lincoln ELEC- Tric Wire FeedersAcross The-Arc Model Control Cable ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the AIR Vantage 500 AUGeneral Description OperationControls and Settings OIL Pressure Gauge Idler SwitchENGINE PROTECTION Output ControlWelding Terminals Switch WELD MODE SELECTOR SWITCHWire Feeder Voltmeter Switch PIN ConnectorAIR Compressor Controls 26 Thru Safety Welding Power SourcesVRD Operation Indicator What are VRD and Rocv DEVICES?BREAK-IN Period Starting TechniqueTypical Fuel Consumption Table b.1 Cummins b3.3 Engine Fuel ConsumptionCC-STICK Mode Stick Welding ModeTouch Start TIG Mode Welder OperationARC Gouging Wire WELDING-CVTable b.3 Typical Current Ranges Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationParalleling PlusOptional Field Installed Accessories AccessoriesTIG Options K2641-2 Four Wheeled STEERAbLE Yard TrailerCompressor Maintenance MaintenanceSingle- and Two-StageEngine Air Cleaners Service InstructionsCooling System Fuel FiltersPreventing Electrical Damage Welder / Generator MAINTE- Nance CleaningStorage Nameplates / Warning Decals MAIN- TenanceTROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionTROUbLESHOOTING Faulty receptacle Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Dimension Print AIR Vantage 500 AU Precaucion Warnung
Top Page Image Contents