Lincoln Electric IM10066 OIL Pressure Gauge, Engine Protection, Idler Switch, Output Control

Page 21

b-3

OPERATION

b-3

 

 

 

7. OIL PRESSURE GAUGE

The gauge displays the engine oil pressure when the engine is running.

8. ENGINE PROTECTION

The yellow engine protection light remains off with proper oil pressure and under normal oper- ating temperatures. If the light turns on, the engine protection system will stop the engine. Check for proper oil level and add oil if neces- sary. Check for loose or disconnected leads at the oil pressure sender located on the engine. The light will remain on when the engine has been shut down due to low oil pressure or over- temperature condition.

9. bATTERY CHARGING LIGHT

The yellow engine alternator light is off when bat- tery charging system is functioning normally. If light turns on the alternator or the voltage regula- tor may not be operating correctly. The light will remain on when the engine is stopped and the run/stop switch is in the run position.

10. IDLER SWITCH

Has two positions as follows:

A)In the “High” position , the engine runs at the high idle speed controlled by the governor.

B) In the “Auto”

/

position, the

idler operates as follows:

 

a. When switched from “High” to “Auto” or after starting the engine, the engine will operate at full speed for approximately 12 seconds and then go to low idle speed.

b. When the electrode touches the work or power is drawn for lights or tools (approximately 100 Watts minimum) the engine accelerates and operates at full speed.

c. When welding ceases and the AC power load is turned off, a fixed time delay of approximate- ly 12 seconds starts.

d. If the welding or AC power load is not restart- ed before the end of the time delay, the idler reduces the engine speed to low idle speed.

e. The engine will automatically return to high idle speed when the welding load or AC power load is reapplied.

Idler Operational exceptions

When the WELDING TERMINALS switch is in the “Remotely Controlled” position the idler will operate as follows:

a. When the triggering device (Amptrol, Arc Start Switch, etc.) is pressed the engine will acceler- ate and operate at full speed provided a weld- ing load is applied within approximately 12 seconds.

•If the triggering device remains pressed but no welding load is applied within approximately 12 seconds the engine may return to low idle speed.

•If the triggering device is released or welding ceases the engine will return to low idle speed after approximately 12 seconds.

WELDING CONTROLS (Items 11 through 20)

11. OUTPUT CONTROL:

The OUTPUT dial is used to preset the output voltage or current as displayed on the digital meters for the four welding modes. When in the

CC-STICK or CV-WIRE modes and when a remote control is connected to the 6-Pin or 14- Pin Connector, the auto-sensing circuit automati- cally switches the OUTPUT CONTROL from con- trol at the welder to the remote control. In the CV-WIRE mode, when the wire feeder control cable is connected to the 14-Pin Connector, the auto-sensing circuit automatically makes OUT- PUT CONTROL inactive and the wire feeder volt- age control active.

When in the TOUCH START TIG mode and when a Amptrol is connected to the 6-Pin Connector, the OUTPUT dial is used to set the maximum current range of the CURRENT CON- TROL of the Amptrol.

12. DIGITAL OUTPUT METERS:

The digital meters allow the output voltage (CV- WIRE mode) or current (CC-STICK and TIG modes) to be set prior to welding using the OUT- PUT control knob. During welding, the meters display the actual output voltage (VOLTS) and current (AMPS). A memory feature holds the dis- play of both meters on the seven seconds after welding is stopped. This allows the operator to read the actual current and voltage just prior to when welding was ceased. While the display is being held the left-most decimal point in each display will be flashing. The accuracy of the meters is ± 3%.

AIR VANTAGE® 500 (AU)

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 11656 Safety Depends on YouCalifornia Proposition 65 Warnings SafetyIiSAFETY Iii IiiSAFETYPrécautions DE Sûreté IvSAFETYElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Vii Please Examine Carton and Equipment For Damage ImmediatelyOn-Line Product Registration TAbLE of Contents TAbLE of Contents Duty Cycle Welding Output Volts at Rated Amps InstallationOpen Circuit Voltage Height Width DepthLocation and Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingOIL PRE-OPERATION Engine and COM- Pressor ServiceFuel USE Diesel Fuel only Fuel CAPMuffler Outlet Pipe AIR Cleaner Inlet HoodSpark Arrestor Welding TerminalsRemote Control Auxiliary Power ReceptaclesSTANDbY Power Connections Connection of LN-15 to the AIR Vantage 500 AU Connection of Lincoln ELEC- Tric Wire FeedersAcross The-Arc Model Control Cable ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the AIR Vantage 500 AUGeneral Description OperationControls and Settings OIL Pressure Gauge Idler SwitchENGINE PROTECTION Output ControlWelding Terminals Switch WELD MODE SELECTOR SWITCHWire Feeder Voltmeter Switch PIN ConnectorAIR Compressor Controls 26 Thru Safety Welding Power SourcesVRD Operation Indicator What are VRD and Rocv DEVICES?BREAK-IN Period Starting TechniqueTypical Fuel Consumption Table b.1 Cummins b3.3 Engine Fuel ConsumptionCC-STICK Mode Stick Welding ModeTouch Start TIG Mode Welder OperationWire WELDING-CV ARC GougingTable b.3 Typical Current Ranges Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationParalleling PlusOptional Field Installed Accessories AccessoriesTIG Options K2641-2 Four Wheeled STEERAbLE Yard TrailerCompressor Maintenance MaintenanceSingle- and Two-StageEngine Air Cleaners Service InstructionsFuel Filters Cooling SystemPreventing Electrical Damage Welder / Generator MAINTE- Nance CleaningStorage Nameplates / Warning Decals MAIN- TenanceTROUbLESHOOTING Symptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionTROUbLESHOOTING Faulty receptacle Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Dimension Print AIR Vantage 500 AU Precaucion Warnung
Top Page Image Contents