Lincoln Electric IM10066 manual Engine Welders / K867 / LN-8 Connection Diagram

Page 43

AIR VANTAGE® 500 (AU)

ENGINE WELDERS / K867 / LN-8 CONNECTION DIAGRAM

WARNING

	Do not operate with panels open.		Keep guards in place.
	Disconnect NEGATIVE (-) BATTERY LEAD		Keep away from moving parts.
	before servicing.	42	Only qualified personnel should install,use
	Do not touch electrically live parts.	42	}
	Do not touch electrically live parts.		or service this equipment.
		SPARE
		82			LN-8
		81	N.C.		WIRE
					FEEDER
		41
		31		31
	14 PIN	32		32
	14 PIN
	AMPHENOL	2		2
		2		2
		4		4	K196
ELECTRODE	TO WORK	21		21	K196
	K867 UNIVERSAL	GND		GND	INPUT CABLE
	ADAPTER PLUG	GND		GND	INPUT CABLE
	ADAPTER PLUG
	TO WORK	75		A
	ELECTRODE CABLE	76		B
	ELECTRODE CABLE	77		B
CAUTION :	TO WIRE FEED UNIT	77	}	C
			}
			N.D.
			N.D.

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE

AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE

DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE

APPICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE SELECTOR SWITCH TO "WIRE WELDING CV".

N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.

N.D. SPLICE LEADS AND INSULATE.

7-2000

S23989

F-6

DIAGRAMS

F-6

Image 43

Contents 11656 Safety Depends on YouCalifornia Proposition 65 Warnings SafetyIiSAFETY Iii IiiSAFETYPrécautions DE Sûreté IvSAFETYElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Please Examine Carton and Equipment For Damage Immediately ViiOn-Line Product Registration TAbLE of Contents TAbLE of Contents Height Width Depth InstallationDuty Cycle Welding Output Volts at Rated Amps Open Circuit VoltageStacking Safety PrecautionsLocation and Ventilation StoringTowing High Temperature OperationLifting High Altitude OperationFuel CAP PRE-OPERATION Engine and COM- Pressor ServiceOIL Fuel USE Diesel Fuel onlyWelding Terminals AIR Cleaner Inlet HoodMuffler Outlet Pipe Spark ArrestorAuxiliary Power Receptacles Remote ControlSTANDbY Power Connections Control Cable Model Connection of Lincoln ELEC- Tric Wire FeedersConnection of LN-15 to the AIR Vantage 500 AU Across The-Arc ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the AIR Vantage 500 AUGeneral Description OperationControls and Settings Output Control Idler SwitchOIL Pressure Gauge ENGINE PROTECTIONPIN Connector WELD MODE SELECTOR SWITCHWelding Terminals Switch Wire Feeder Voltmeter SwitchAIR Compressor Controls 26 Thru What are VRD and Rocv DEVICES? Welding Power SourcesSafety VRD Operation IndicatorTable b.1 Cummins b3.3 Engine Fuel Consumption Starting TechniqueBREAK-IN Period Typical Fuel ConsumptionWelder Operation Stick Welding ModeCC-STICK Mode Touch Start TIG ModeARC Gouging Wire WELDING-CVTable b.3 Typical Current Ranges Plus Auxiliary Power OperationSimultaneous Welding and AUXIL- Iary Power Loads ParallelingK2641-2 Four Wheeled STEERAbLE Yard Trailer AccessoriesOptional Field Installed Accessories TIG OptionsCompressor Maintenance MaintenanceSingle- and Two-StageEngine Air Cleaners Service InstructionsCooling System Fuel FiltersPreventing Electrical Damage Nameplates / Warning Decals MAIN- Tenance CleaningWelder / Generator MAINTE- Nance StorageTROUbLESHOOTING Cause Recommended Course of Action PRObLEMSSymptoms POSSIbLETROUbLESHOOTING Faulty receptacle Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Dimension Print AIR Vantage 500 AU Precaucion Warnung