Lincoln Electric SVM161-A service manual Input Filter Capacitor Discharge Procedure

Page 54

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

F-14	TROUBLESHOOTING AND REPAIR	F-14

INPUT FILTER CAPACITOR DISCHARGE PROCEDURE (continued)

FIGURE F.3 – LOCATION OF INPUT FILTER CAPACITOR TERMINALS ON MAIN IGBT INVERTER BOARD

Capacitor Solder

Resistor Pads

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

WARNING

ELECTRIC SHOCK can kill.

•Have an electrician install and ser- vice this equipment.

•Turn the input power off at the fuse box before working on equipment.

•Do not touch electrically hot parts.

•Prior to performing preventative maintenance, perform the following capacitor discharge proce- dure to avoid electric shock.

DISCHARGE PROCEDURE

1.Remove the input power to the machine.

2.Using the phillips head screwdriver remove the screws securing the case wraparound cover.

3.Be careful not to make contact with the capac- itor solder pads located at the top of the IGBT power board.

4.Obtain a high resistance and high wattage resistor (25-1000 ohms and 25 watts mini- mum). This resistor is not with the machine.

NEVER USE A SHORTING STRAP FOR THIS PROCEDURE.

5.Locate the eight capacitor solder pads shown in Figure F.3.

6.Using electrically insulated gloves and pliers, hold the body of the resistor with the pliers and connect the resistor leads across the two capacitor solder pads. Hold the resistor in place for 10 seconds. DO NOT TOUCH CAPACITOR SOLDER PADS WITH YOUR BARE HANDS.

7.Repeat the discharge procedure for the other three capacitors.

8.Check the voltage across the terminals of all capacitors with a DC voltmeter. Voltage should be zero. If any voltage remains, repeat this capacitor discharge procedure.

INVERTEC® V205-T AC/DC™

Image 54

Contents Invertec V205-T AC/DC Safety Invertec V205-T AC/DCElectric Shock can kill ARC Rays can burn Can be dangerousCylinder may explode Powered equipmentWelding Cutting Sparks can cause fire or If damaged ExplosionPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcSafety Methods of Reducing Emissions Mains Supply Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Operating Temperature Range Storage Temperature RangeTilting Select Suitable LocationStacking Environmental AreaReconnect Procedure Input Connections115V Input Attachment Plug Installation230V Input Engine Driven GeneratorOutput Connections Output and GAS Connection for TIG Welding Figure A.1Work Cable Connection Remote Control Connection Shielding GAS ConnectionInvertec V205-T AC/DC Table of Contents Operation Section General Description Safety InstructionsOperation Welding CapabilityOPERATIONB-3 Rear Control Panel Figure B.1Controls and Settings Figure B.2Step Diagram Local/Remote push button Selects the weldingTIG DC TIG AC SET UP Menu Indicator Parameter DefaultOutput Limitations Welding PolarityFigure B.7 Tips for AC TIG Welding Steel TIG WeldingCopper TIG Welding Filler MaterialAC TIG Welding Quick Start UP Protective GASDC TIG Welding Quick Start UP Table of Contents Accessories Section Compatible Equipment AccessoriesOptional Accessories Cable PlugsTable of Contents Maintenance Section Input Filter Capacitor Discharge Procedure MaintenanceSafety Precautions Routine Maintenance3MAINTENANCE Figure D.1 Major Component LocationsInvertec V205-T AC/DC 1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Input Board and BUS BoardMain Igbt Inverter Board Figure E.3 Main Igbt Inverter BoardOutput Module and Clamping Board Main TransformerOutput Module Transistor Board Superimposition BoardCONTROL/DISPLAY Board High Frequency HF BoardOutput Filter Board Insulated Gate Bipolar Transistor Igbt Operation Passive Active1TABLE of Contents Troubleshooting and Repair F-1 Troubleshooting and Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Electric Shock can killIgbt Perform the Input Filter Board Igbt Inverter Board Test Secondary Output Board Assembly Test See the Output Filter Troubleshooting and Repair External Diagnostics DisplayTroubleshooting and Repair Internal Diagnostics Figure F.2Internal Diagnostics LEDInvertec V205-T AC/DC Test Description Materials NeededInput Filter Capacitor Discharge Procedure Capacitor Solder Resistor PadsInput Filter Board Test Procedure Input Filter Board TestInput Filter Board Input Filter Board Invertec V205-T AC/DC Main Igbt Inverter Board LOW Voltage Test Main Igbt Inverter Board LOW Voltage Test Figure F.6 Main Igbt Inverter Board LocationMain Igbt Inverter Board LOW Voltage Test LEDTP2 MF2 Figure F.7 Main Igbt Inverter Board LocationCONTROL/DISPLAY Board Test CONTROL/DISPLAY Board Test Figure F.8 CONTROL/DISPLAY Board LocationCN2 Figure F.9 CONTROL/DISPLAY Board LocationCN1 Figure F.10 Plugs CN1, CN2 & CN7BUS Board Test BUS Board Test Figure F.11 BUS Board LocationTable F.7 Plug CN4 Test Points Table F.5 Plug CN2 Test PointsTable F.6 Plug CN3 Test Points Table F.8 Plug CN7 Test PointsCN1 CN2 Main Inverter Board Power Factor Section Test Main Inverter Board Power Factor Section Test Table F.10 Voltage Checks with 115 VAC Applied to MachineTable F.11 Resistance Checks TP9 Gndpwr RL1 Invertec V205-T AC/DC Output Filter Board Test Output Filter Board Test Figure F.16 Output Filter Board LocationFigure F.17 Output Filter Board Plug Location Figure F.18 Output Filter Board Plug CN1Invertec V205-T AC/DC Secondary Output Board Assembly Test Secondary Output Board Assembly Test Figure F.19 Secondary Power Board LocationOFF GA-SA Mode Positive Meter Negative Meter Expected Reading Probe Table F.14 Output Diode Resistance CheckMain Inverter Board Welding Logic and Inverter Section Test Main Inverter Board Welding Logic and Inverter Section TestTable F.15 LED Function Table F.16 Feedback Voltage SignalsTable F.18 LED Check in Stick Mode Table F.17 Voltage Checks with 115 VAC Applied to MachineFigure F.22 Main Board Inverter Section TP9 Ground Power Invertec V205-T AC/DC Input Filter Board Removal and Replacement Input Filter Board Removal and Replacement Figure F.24 Input Filter Board LocationRV1 RV2 Invertec V205-T AC/DC Main Igbt Board Removal and Replacement Main Igbt Board Removal and Replacement Figure F.27 Main Igbt Board LocationRV1 RV2 CN4 RV3 RV4 CN5 RV5 RV7 RV6 Invertec V205-T AC/DC CONTROL/DISPLAY Board Removal and Replacement CONTROL/DISPLAY Board Removal and Replacement Figure F.29 CONTROL/DISPLAY Board LocationCN2 Invertec V205-T AC/DC Output Filter Board Removal and Replacement Removal and Replacement Figure F.32 Output Filter Board LocationPhillips Head Screws CN1 Output Diodes Removal and Replacement Output Diodes Removal and Replacement To Replace ANY of the Output Diodes D1, D2, D3 or D4Output Transistor Removal and Replacement Output Transistor Removal and Replacement Figure F.36 Output Transistor LocationPlug CN1 5mm Allen Bolts Invertec V205-T AC/DC Table of Contents Diagram Section ELECTriCaL DiaGramS