Skil 7305 manual Operating Instructions, Rocker ON/OFF Switch

Page 11

SM 1619X04464 05-09:SM 1619X04464 05-09 5/20/09 1:54 PM Page 11

Operating Instructions

ROCKER “ON/OFF” SWITCH

TO TURN THE TOOL "ON" depress the dust-protected switch to the number “I” position.

TO TURN THE TOOL "OFF": depress switch to the number “0” position (Fig. 9).

Hold the tool with both hands while starting the tool, since torque from the motor can cause the tool to twist.

FIG. 9

ROCKER

“ON/OFF”

SWITCH

RELEASING AND INSERTING

BATTERy PACK

Release battery pack from tool by pressing the battery release button and sliding pack out of

handle base (Fig. 1). To insert battery, align battery and slide battery pack into tool until it locks into position. Do not force.

IMPORTANT CHARGING NOTES (NICKEL-CADMIUM BATTERIES)

1.The battery pack accepts only about 80% of its maximum capacity with its first few charge cycles. However, after the first few charge cycles, the battery will charge to full capacity.

2.The charger was designed to fast charge the battery only when the battery temperature is between 32˚F (0˚C) and 113˚F (45˚C).

3.A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced.

4.If you anticipate long periods (i.e. a month or more) of non-use of your tool, it is best to run your tool down until it is fully discharged before storing your battery pack. After a long period of storage, the capacity at first recharge

will be lower. Normal capacity will be restored in two or three charge/discharge cycles. Remember to unplug charger during storage period.

5.If battery does not charge properly:

a.Check for voltage at outlet by plugging in some other electrical device.

b.Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off.

c.Check battery pack terminals for dirt. Clean with cotton swab if necessary.

d.If you still do not get proper charging, take or send tool, battery pack and charger to your local Skil Service Center.

Note: Use of charger’s or battery packs not sold by Skil will void the warranty.

BATTERy CHARGED CONDITION INDICATOR (SB18B BATTERy)

Your battery pack is equipped with charge condition indicator lights (Fig. 10). The indicator lights shows the charge condition of the battery during operation.

To check battery charge condition, depress and hold the button on the backside of the battery pack.

• • • • When all five lights are illuminated, this indicates the batter pack is fully charged.

• • When only three lights illuminate, this indicates the battery pack is partially charged.

When only one light illuminates, this indicates the battery pack is slightly charged.

When no lights illuminate, this indicates the battery pack is completely discharged.

-11-

Image 11
Contents See Voir Ver la página Leer antes de usarCall Toll Free for Personal safety General Power Tool Safety WarningsWork area safety Electrical safetyService Safety Rules for Orbital SandersBattery tool use and care Battery/Charger LITHIUM-ION Batteries Battery CareBattery Disposal NICKEL-CADMIUM BatteriesName Designation/Explanation SymbolsSymbols Lights Button Not Available on ALL Models Functional Description and SpecificationsBattery Release Button Cordless Multi-Finishing SanderLatches Rotating Backing PAD AssemblyInstalling Sanding Sheets PAD/PLATE Backing Unlockpad ButtonAttaching the 3-POSITION Attachment Support Plate Attaching AccessoriesAdjustment Rail Release TAB PAD/PLATE Unlock Button BackingOperating Instructions Rocker ON/OFF SwitchRocker ON/OFF Switch Releasing and Inserting BATTERy Charged Condition Indicator SB18B BATTERyCondition Indicator Lights Charger Charging BATTERy Pack SC118 or SC118B ChargerNot Available on ALL Models Button Battery Pack Mounting Charger Lights LED Important Charging Notes LITHIUM-ION BatteriesTool Tips Battery Pack Indicator Light ChargerApplication Advice Optional 9 Piece ACCESSORy KIT # Cleaning MaintenanceAccessories Trouble BATTERy Pack will not Charge Trouble ShootingProblem Trouble Tool will not Start Sécurité électrique Sécurité du lieu de travailEntretien Consignes de sécurité pour perceuses/tournevis sans cordonUtilisation et entretien des outils Électroportatifs Utilisation et entretien des outils à pilesLe plomb provenant des peintures à base de plomb Chargeur de pilePiles LITHIUM-ION Entretien des pilesMise au rebut des piles Piles NICKEL-CADMIUMSymbole Nom Désignation/Explication SymbolesSymboles suite SB18B-LI Description fonctionnelle et spécificationsPonceuse sans fil pour travaux de finition multiples Plateau PORTE-OUTILS Rotatif AssemblageRetrait ET Mise EN Place DU Plateau PORTE-OUTILS Rail DE Réglage Languette DE Déverrouillage Accessoires À 3 PositionsFixation DES Accessoires Plaque DE RallongeDepose ET Repose DU BLOC-PILES Consignes de fonctionnementInterrupteur À Bascule MARCHE/ARRÊT InterrupteurCharge DU BLOC-PILES Témon Lumineux Chargement DU BLOC-PILES Chargeur SC118 OU SC118BCompartiment DE Rangement DES Embouts Chargeur Montage du chargeurMontage DU Chargeur À UNE Surface Verticale Modèles SC118 et SC118B seulementMessage d’erreur Accessoire EN OptionTémoins D’ÉTAT DE Charge DU BLOC-PILES BLOC-PILES SB18B-LI DELUsage Conseils pratiquesBloc Piles Témon Lumineux Chargeur Applications recommandées LOT Daccessoires Facultatif DE 9 Morceaux # Nettoyage AccessoiresEntretien Problème LE BLOC-PILES NE Charge PAS Guide de diagnosticProblème L’OUTIL NE Démarre PAS Seguridad personal Seguridad del área de trabajoSeguridad eléctrica Servicio de ajustes y reparaciones Uso y cuidado de las herramientas Alimentadas por bateríasBatería/cargador Baterías DE Iones DE Litio Cuidado de las bateríasEliminación de las baterías Baterías DE NIQUEL-CADMIOSímbolo Nombre Designación/explicación SímbolosSímbolos continuación No Disponible EN Todos LOS Modelos Descripción funcional y especificacionesLijadora de multiacabado inalámbrica Botón DE Liberación DE LA BateríaInstalación DE Hojas DE Lijar EnsamblajeRemoción E Instalación DE LA Zapata DE Soporte Zapata DE Soporte RotatoriaRiel DE Ajuste Placa DE ExtensiónAditamentos DE 3 Posiciones Instalación DE AccesoriosNotas Importantes Para Cargar Baterías DE NIQUEL-CADMIO Instrucciones de funcionamientoCargador Carga DEL Paquete DE Baterías Cargador SC118 OU SC118BBotón Para Desbloquear Bloquear Paquete DE Batería Cargador Montaje del cargadorMontaje DEL Cargador EN UNA Superficie Vertical Modelos SC118 y SC118B solamenteCarga DEL Paquete DE Batería Cargador SC118B-LI Accesorio OpcionalNotas Importantes Para Cargar Baterías DE Iones DE Litio LUZ LEDAplicación Consejos para la herramientaPaquete DE Baterías LUZ Indicadora Cargador Consejos de aplicación KIT DE Accesorios Opcional DE 9 Pedazos # Limpieza MantenimientoAccesorios ServicioAvería EL Paquete DE Batería no SE Carga Resolución de problemasAvería LA Herramienta no Arranca SM 1619X04464 05-09SM 1619X04464 05-09 5/20/09 154 PM