Grizzly G0555 owner manual Identification

Page 5

		Identification
			L
	A		M
			M
			N
			P
	B		O
	D	E	Q
C			Q
C
		F	R
I		G
I
	J	H	S
	J		S
			T
K			U
K	Front		Rear
	View		View

Figure 1. G0555/G0555P identification.

A.	Upper Wheel Cover	L.	Blade Tension Adjustment Knob
B.	ON/OFF Switch w/Disabling Padlock	M.	Blade Tension Quick Release Lever
C.	Fence	N.	Guide Post
D.	Blade Guard	O.	Guide Post Lock Knob
E.	Upper Blade Guide Assembly	P.	Blade Tension Scale
F.	Table Pin	Q.	Blade Tracking Adjustment Knob
G.	Miter Gauge Assembly	R.	Table Insert
H.	Lower Wheel Cover	S.	Rear Table Lock Knob
I.	Fence Lock Lever	T.	4" Dust Port
J.	Front Table Lock Knob	U.	Motor

K.Stand Assembly

To reduce the risk of serious injury when using this machine, read and understand this entire manual before beginning any operations.

Model G0555/G0555P (Mfg. Since 5/11)

-3-

Image 5

Contents Ultimate 14 Bandsaw Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification MaCHiNe data SHeet Table Information Safety Instructions for Machinery SafetyPage Additional Safety for Bandsaws Availability Power SupplyFull-Load Current Rating Circuit InformationShock Hazard Grounding RequirementsVoltage Conversion Extension CordsMinimum Gauge Size 14 AWG 50 ftNeeded for Setup SetupUnpacking Description QtyHardware Recognition Chart Shipping Inventory Figures Qty InventoryBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Ing the stand easier in a later step AssemblyLeveling the stand Trunnion Page Fence stand-off installed Model G0555/G0555P Mfg. Since 5/11 To center track the blade Blade Center TrackingTo connect a dust collection hose Dust CollectionConnecting Power Power Connection Test RunDisconnecting Power To test run the machineTo tension the bandsaw blade Tensioning BladeTo adjust the support bearings Adjusting Blade Support BearingsTool Needed Qty Adjusting Blade Guide BearingsTo adjust the upper and lower blade guides Page To set the positive stop 90˚ to the blade Table Tilt CalibrationTools Needed Qty Step Aligning TableTo align the table to the blade Aligning Fence Operation Overview OperationsBefore cutting, inspect all workpieces for the following Disabling & Locking SwitchWorkpiece Inspection To tilt the table To adjust the height of the guide postGuide Post Table Tilt To change the blade speed Blade SpeedBlade Information Blade DimensionsBlade Length Blade WidthBlade Care Tooth PitchBlade Breakage Most common causes of blade breakage areBlade Removal Blade InstallationBlade Change Cutting Options Basic Cutting TipsRipping To make a rip cutTo make a 90˚ crosscut CrosscuttingResawingTo complete a stacked cut Cutting Curves Stacked CutsBandsaw Blades AccessoriesModel G1928-Bandsaw HandbookH7584-Re-Saw Fence Retrofit Kit G7315Z-Super Heavy-Duty Shop FOX Mobile BaseCleaning Protecting MaintenanceSchedule DailyTo redress the rubber tires LubricationRedressing Rubber Tires Motor & Electrical ServiceTroubleshooting Miscellaneous Cutting OperationsChecking V-Belt Tension Belt TensionTensioning V-Belt To properly tension the V-beltShimming Table Replacing V-BeltTo replace the V-belt Belt Tension subsection onChecking Wheel Alignment Wheel AlignmentTo shim a wheel Shimming a WheelTo adjust the upper wheel laterally Upper Wheel Lateral AdjustmentTo correct blade lead Blade LeadTo skew your fence To shift the tableBlade Tensioner To reset the blade tensionerTo calibrate the scale Fence Scale CalibrationWiring Safety Instructions Wiring110 VAC Wiring DiagramMain Description Main Parts ListDescription Stand Fence 144V2 216 155 145 148 147 149 157 156 218 217 214 LabelsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY

Related manuals

Manual 55 pages 21 Kb