Grizzly G0555 owner manual Aligning Fence

Page 32

Aligning Fence

To ensure accurate cutting when using the fence, the face of the fence must be parallel to the table miter slot and, thus, to the side of the blade.

Tools Needed	Qty
Hex Wrench 5mm.	..............................................1

To align the fence parallel with the miter slot:

1.Make sure the miter slot is parallel with the blade, as instructed in the previous Aligning Table procedure.

2.DISCONNECT BANDSAW FROM POWER!

3.Install the fence on the right side of the blade, even with the edge of the miter slot, then lock it in place.

—If the fence is parallel with the miter slot, no adjustment is necessary.

—If the fence is not parallel with the miter slot, proceed to Step 4.

-30-

4.Loosen the four fence adjustment cap screws shown in the figure below, adjust the fence parallel to the miter slot, then re-tighten the cap screws to secure the setting.

Cap Screws

Figure 41. Location of the fence adjustment cap

screws.

Model G0555/G0555P (Mfg. Since 5/11)

Image 32

Contents Ultimate 14 Bandsaw Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification MaCHiNe data SHeet Table Information Safety Safety Instructions for MachineryPage Additional Safety for Bandsaws Power Supply AvailabilityFull-Load Current Rating Circuit InformationGrounding Requirements Shock HazardExtension Cords Voltage ConversionMinimum Gauge Size 14 AWG 50 ftSetup Needed for SetupUnpacking Description QtyHardware Recognition Chart Inventory Shipping Inventory Figures QtyBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Assembly Ing the stand easier in a later stepLeveling the stand Trunnion Page Fence stand-off installed Model G0555/G0555P Mfg. Since 5/11 Blade Center Tracking To center track the bladeDust Collection To connect a dust collection hosePower Connection Test Run Connecting PowerDisconnecting Power To test run the machineTensioning Blade To tension the bandsaw bladeAdjusting Blade Support Bearings To adjust the support bearingsTool Needed Qty Adjusting Blade Guide BearingsTo adjust the upper and lower blade guides Page To set the positive stop 90˚ to the blade Table Tilt CalibrationTools Needed Qty Step Aligning TableTo align the table to the blade Aligning Fence Operations Operation OverviewBefore cutting, inspect all workpieces for the following Disabling & Locking SwitchWorkpiece Inspection To tilt the table To adjust the height of the guide postGuide Post Table Tilt Blade Speed To change the blade speedBlade Dimensions Blade InformationBlade Length Blade WidthTooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areBlade Removal Blade InstallationBlade Change Basic Cutting Tips Cutting OptionsRipping To make a rip cutCrosscuttingResawing To make a 90˚ crosscutCutting Curves Stacked Cuts To complete a stacked cutAccessories Bandsaw BladesModel G1928-Bandsaw HandbookG7315Z-Super Heavy-Duty Shop FOX Mobile Base H7584-Re-Saw Fence Retrofit KitMaintenance Cleaning ProtectingSchedule DailyTo redress the rubber tires LubricationRedressing Rubber Tires Motor & Electrical ServiceTroubleshooting Cutting Operations MiscellaneousBelt Tension Checking V-Belt TensionTensioning V-Belt To properly tension the V-beltReplacing V-Belt Shimming TableTo replace the V-belt Belt Tension subsection onWheel Alignment Checking Wheel AlignmentShimming a Wheel To shim a wheelUpper Wheel Lateral Adjustment To adjust the upper wheel laterallyBlade Lead To correct blade leadTo skew your fence To shift the tableTo reset the blade tensioner Blade TensionerFence Scale Calibration To calibrate the scaleWiring Wiring Safety InstructionsWiring Diagram 110 VACMain Main Parts List DescriptionDescription Stand Fence Labels 144V2 216 155 145 148 147 149 157 156 218 217 214Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY

Related manuals

Manual 55 pages 21 Kb