Grizzly G0555 owner manual MaCHiNe data SHeet

Page 6

maCHiNe data

SHeet

© Grizzly Industrial, Inc. • Customer Service: (800) 523-4777 • Website: www.grizzly.com

model G0555/G0555P
ultimate 14" BaNdSaW
Product Dimensions:
Weight	167 lbs.
Length/Width/Height	263⁄8" x 301⁄4" x 661⁄2"
Foot Print (Length/Width)	241⁄2" x 171⁄2"
Shipping Dimensions:
Type	Cardboard
Content	Machine
Weight	198 lbs.
Length/Width/Height	44" x 21" x 20"
Electrical:
Switch	On/Off Push Button
Switch Voltage	110/220V
Cord Length	6 ft.
Cord Gauge	16 gauge
Minimum Circuit Size	15A @ 110V, 10A @ 220V
Plug Included	Yes
Recommended Plug Type	NEMA 6-15 @220V
Included Plug Type	NEMA 5-15
Motors:
Main
Type	TEFC Capacitor Start Induction
Horsepower	1 HP
Voltage	110V/220V
Prewired	110V
Phase	Single
Amps	11/5.5A
Speed	1725 RPM
Cycle	60 Hz
Number Of Speeds	1
Power Transfer	Belt Drive
Bearings	Shielded and Lubricated
Main Specifications:
Operation Information
Blade Speed	1500, 3200 FPM
Table Tilt	Left 10°, Right 45°
Cutting Capacities
Maximum Cutting Height	6"
Max Capacity Left of Blade	131⁄2"

-4-	Model G0555/G0555P (Mfg. Since 5/11)

Image 6

Contents Ultimate 14 Bandsaw Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification MaCHiNe data SHeet Table Information Safety Safety Instructions for MachineryPage Additional Safety for Bandsaws Full-Load Current Rating Power SupplyAvailability Circuit InformationGrounding Requirements Shock HazardMinimum Gauge Size 14 AWG Extension CordsVoltage Conversion 50 ftUnpacking SetupNeeded for Setup Description QtyHardware Recognition Chart Inventory Shipping Inventory Figures QtyCleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Assembly Ing the stand easier in a later stepLeveling the stand Trunnion Page Fence stand-off installed Model G0555/G0555P Mfg. Since 5/11 Blade Center Tracking To center track the bladeDust Collection To connect a dust collection hoseDisconnecting Power Power Connection Test RunConnecting Power To test run the machineTensioning Blade To tension the bandsaw bladeAdjusting Blade Support Bearings To adjust the support bearingsAdjusting Blade Guide Bearings To adjust the upper and lower blade guidesTool Needed Qty Page Table Tilt Calibration Tools Needed QtyTo set the positive stop 90˚ to the blade Aligning Table To align the table to the bladeStep Aligning Fence Operations Operation OverviewDisabling & Locking Switch Workpiece InspectionBefore cutting, inspect all workpieces for the following To adjust the height of the guide post Guide Post Table TiltTo tilt the table Blade Speed To change the blade speedBlade Length Blade DimensionsBlade Information Blade WidthBlade Breakage Tooth PitchBlade Care Most common causes of blade breakage areBlade Installation Blade ChangeBlade Removal Ripping Basic Cutting TipsCutting Options To make a rip cutCrosscuttingResawing To make a 90˚ crosscutCutting Curves Stacked Cuts To complete a stacked cutModel AccessoriesBandsaw Blades G1928-Bandsaw HandbookG7315Z-Super Heavy-Duty Shop FOX Mobile Base H7584-Re-Saw Fence Retrofit KitSchedule MaintenanceCleaning Protecting DailyLubrication Redressing Rubber TiresTo redress the rubber tires Service TroubleshootingMotor & Electrical Cutting Operations MiscellaneousTensioning V-Belt Belt TensionChecking V-Belt Tension To properly tension the V-beltTo replace the V-belt Replacing V-BeltShimming Table Belt Tension subsection onWheel Alignment Checking Wheel AlignmentShimming a Wheel To shim a wheelUpper Wheel Lateral Adjustment To adjust the upper wheel laterallyTo skew your fence Blade LeadTo correct blade lead To shift the tableTo reset the blade tensioner Blade TensionerFence Scale Calibration To calibrate the scaleWiring Wiring Safety InstructionsWiring Diagram 110 VACMain Main Parts List DescriptionDescription Stand Fence Labels 144V2 216 155 145 148 147 149 157 156 218 217 214Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY

Related manuals

Manual 55 pages 21 Kb