Grizzly G0555 owner manual Wiring Safety Instructions

Page 57

machine

SECTION 8: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make chang- es to the electrical systems of future machines. Compare the manufacture date of your machine to the one stated in this manual, and study this section carefully.

If there are differences between your machine and what is shown in this section, call Technical Support at

(570)546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated wiring diagram may be available. Note: Please gather the serial number and manufacture date of your machine before calling. This information can be found on the main machine label.

Wiring Safety Instructions

SHOCK HAZARD. Working on wiring that is con- nected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before servicing electrical com- ponents!

MODIFICATIONS. Modifying the wiring beyond what is shown in the diagram may lead to unpre- dictable results, including serious injury or fire. This includes the installation of unapproved after- market parts.

WIRE CONNECTIONS. All connections must be tight to prevent wires from loosening during machine operation. Double-check all wires dis- connected or connected during any wiring task to ensure tight connections.

CIRCUIT REQUIREMENTS. You MUST follow the requirements at the beginning of this man- ual when connecting your machine to a power source.

WIRE/COMPONENT DAMAGE. Damaged wires or components increase the risk of serious per- sonal injury, fire, or machine damage. If you notice that any wires or components are damaged while performing a wiring task, replace those wires or components.

MOTOR WIRING. The motor wiring shown in these diagrams is current at the time of printing but may not match your machine. If you find this to be the case, use the wiring diagram inside the motor junction box.

CAPACITORS/INVERTERS. Some capacitors and power inverters store an electrical charge for up to 10 minutes after being disconnected from the power source. To reduce the risk of being shocked, wait at least this long before working on capacitors.

EXPERIENCING DIFFICULTIES. If you are expe- riencing difficulties understanding the information included in this section, contact our Technical Support at (570) 546-9663.

The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com.

Model G0555/G0555P (Mfg. Since 5/11)

-55-

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Ultimate 14 Bandsaw Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description Identification MaCHiNe data SHeet Table Information Safety Instructions for Machinery SafetyPage Additional Safety for Bandsaws Availability Power SupplyFull-Load Current Rating Circuit InformationShock Hazard Grounding RequirementsVoltage Conversion Extension CordsMinimum Gauge Size 14 AWG 50 ftNeeded for Setup SetupUnpacking Description QtyHardware Recognition Chart Shipping Inventory Figures Qty InventoryCleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Ing the stand easier in a later step AssemblyLeveling the stand Trunnion Page Fence stand-off installed Model G0555/G0555P Mfg. Since 5/11 To center track the blade Blade Center TrackingTo connect a dust collection hose Dust CollectionConnecting Power Power Connection Test RunDisconnecting Power To test run the machineTo tension the bandsaw blade Tensioning BladeTo adjust the support bearings Adjusting Blade Support BearingsAdjusting Blade Guide Bearings To adjust the upper and lower blade guidesTool Needed Qty Page Table Tilt Calibration Tools Needed QtyTo set the positive stop 90˚ to the blade Aligning Table To align the table to the bladeStep Aligning Fence Operation Overview OperationsDisabling & Locking Switch Workpiece InspectionBefore cutting, inspect all workpieces for the following To adjust the height of the guide post Guide Post Table TiltTo tilt the table To change the blade speed Blade SpeedBlade Information Blade DimensionsBlade Length Blade WidthBlade Care Tooth PitchBlade Breakage Most common causes of blade breakage areBlade Installation Blade ChangeBlade Removal Cutting Options Basic Cutting TipsRipping To make a rip cutTo make a 90˚ crosscut CrosscuttingResawingTo complete a stacked cut Cutting Curves Stacked CutsBandsaw Blades AccessoriesModel G1928-Bandsaw HandbookH7584-Re-Saw Fence Retrofit Kit G7315Z-Super Heavy-Duty Shop FOX Mobile BaseCleaning Protecting MaintenanceSchedule DailyLubrication Redressing Rubber TiresTo redress the rubber tires Service TroubleshootingMotor & Electrical Miscellaneous Cutting OperationsChecking V-Belt Tension Belt TensionTensioning V-Belt To properly tension the V-beltShimming Table Replacing V-BeltTo replace the V-belt Belt Tension subsection onChecking Wheel Alignment Wheel AlignmentTo shim a wheel Shimming a WheelTo adjust the upper wheel laterally Upper Wheel Lateral AdjustmentTo correct blade lead Blade LeadTo skew your fence To shift the tableBlade Tensioner To reset the blade tensionerTo calibrate the scale Fence Scale CalibrationWiring Safety Instructions Wiring110 VAC Wiring DiagramMain Description Main Parts ListDescription Stand Fence 144V2 216 155 145 148 147 149 157 156 218 217 214 LabelsComments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCWarranty and Returns Warranty and ReturnsOrder Hours a DAY
Related manuals
Manual 55 pages 21 Kb
Top Page Image Contents