Grizzly G0555 owner manual Stand

Page 62

202

201

	Stand
	205	206
	204	206
	204	207
		208
	211
	212

212 211 213

209

210

REF	PART #	DESCRIPTION

201	P0555201	STAND TOP (G0555)
201	P0555P201	STAND TOP (G0555P)
202	PCB06M	CARRIAGE BOLT M8-1.25 X 16

204	PFN01M	FLANGE NUT M8-1.25

205	P0555205	STAND SIDE (G0555)

205	P0555P205	STAND SIDE (G0555P)
206	PB83M	HEX BOLT M6-1 X 16
207	PW03M	FLAT WASHER 6MM

REF	PART #	DESCRIPTION

208	PFN02M	FLANGE NUT M6-1
209	P0555209	UPPER STAND BRACE (G0555)
209	P0555P209	UPPER STAND BRACE (G0555P)

210	P0555210	LOWER STAND BRACE (G0555)

210	P0555P210	LOWER STAND BRACE (G0555P)

211	PN08	HEX NUT 3/8-16
212	PW04M	FLAT WASHER 10MM
213	P0555213	STAND FOOT

-60-	Model G0555/G0555P (Mfg. Since 5/11)

Image 62

Contents Ultimate 14 Bandsaw Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification MaCHiNe data SHeet Table Information Safety Safety Instructions for MachineryPage Additional Safety for Bandsaws Full-Load Current Rating Power SupplyAvailability Circuit InformationGrounding Requirements Shock HazardMinimum Gauge Size 14 AWG Extension CordsVoltage Conversion 50 ftUnpacking SetupNeeded for Setup Description QtyHardware Recognition Chart Inventory Shipping Inventory Figures QtyBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Assembly Ing the stand easier in a later stepLeveling the stand Trunnion Page Fence stand-off installed Model G0555/G0555P Mfg. Since 5/11 Blade Center Tracking To center track the bladeDust Collection To connect a dust collection hoseDisconnecting Power Power Connection Test RunConnecting Power To test run the machineTensioning Blade To tension the bandsaw bladeAdjusting Blade Support Bearings To adjust the support bearingsTool Needed Qty Adjusting Blade Guide BearingsTo adjust the upper and lower blade guides Page To set the positive stop 90˚ to the blade Table Tilt CalibrationTools Needed Qty Step Aligning TableTo align the table to the blade Aligning Fence Operations Operation OverviewBefore cutting, inspect all workpieces for the following Disabling & Locking SwitchWorkpiece Inspection To tilt the table To adjust the height of the guide postGuide Post Table Tilt Blade Speed To change the blade speedBlade Length Blade DimensionsBlade Information Blade WidthBlade Breakage Tooth PitchBlade Care Most common causes of blade breakage areBlade Removal Blade InstallationBlade Change Ripping Basic Cutting TipsCutting Options To make a rip cutCrosscuttingResawing To make a 90˚ crosscutCutting Curves Stacked Cuts To complete a stacked cutModel AccessoriesBandsaw Blades G1928-Bandsaw HandbookG7315Z-Super Heavy-Duty Shop FOX Mobile Base H7584-Re-Saw Fence Retrofit KitSchedule MaintenanceCleaning Protecting DailyTo redress the rubber tires LubricationRedressing Rubber Tires Motor & Electrical ServiceTroubleshooting Cutting Operations MiscellaneousTensioning V-Belt Belt TensionChecking V-Belt Tension To properly tension the V-beltTo replace the V-belt Replacing V-BeltShimming Table Belt Tension subsection onWheel Alignment Checking Wheel AlignmentShimming a Wheel To shim a wheelUpper Wheel Lateral Adjustment To adjust the upper wheel laterallyTo skew your fence Blade LeadTo correct blade lead To shift the tableTo reset the blade tensioner Blade TensionerFence Scale Calibration To calibrate the scaleWiring Wiring Safety InstructionsWiring Diagram 110 VACMain Main Parts List DescriptionDescription Stand Fence Labels 144V2 216 155 145 148 147 149 157 156 218 217 214Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty and Returns Warranty and ReturnsOrder Hours a DAY

Related manuals

Manual 55 pages 21 Kb