Grizzly G0648 owner manual Inventory, Crate 1 Figure Qty, Box 2 Figure Qty

Page 14

Inventory

The following is a description of the main compo- nents shipped with your machine. Lay the compo- nents out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for shipping purposes.

Crate 1: (Figure 3)	Qty
A. Welding Fume Extractor Unit	...................... 1

B.Button Head Cap Screws 3/8"-16 x 1"

.	(Ducting Arm)	6
C.	Flat Washer 3/8" (Ducting Arm)	6
D.	Roller Filter Paper (Pre-Installed Roll)	1
E.	Door Levers	2
F.	Downdraft Table Adapter Box	1
G.	Bolt Bag	1
.	—Hex Bolts 3/8"-16 x 3/4" (Adapter Box)	6
.	—Flat Washers 3/8" (Adapter Box)	6
Box 2: (Figure 4)		Qty
H.	Ducting Arm and Shroud Assembly	1

SUFFOCATION HAZARD!

Immediately discard all plastic bags and packing materials to eliminate choking/suffocation hazards for children and animals.

-12-

B C

A

F	G	D

E

Figure 3. Welding fume extractor unit.

H

Figure 4. Ducting arm assembly.

If any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

G0648 Welding Fume Extractor

Image 14

Contents Model G0648 Welding Fume Extractor Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Vibrating Filter & Hepa Filter Housing IdentificationMachine Data Sheet Other Specifications !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Welding Fume Extractors Meeting Welding Fume Extraction Codes Standards 220V 3-Phase Operation Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingBox 2 Figure Qty InventoryCrate 1 Figure Qty Hardware Recognition Chart Site Considerations Floor LoadTest Run Ducting Arm InstallationTo install the ducting arm To test run the machineCompletely open both blast gates on the ducting arm Figure To use the machine Operation Safety General OperationOperations Page Control Panel Operation Setting Time Left Button ControlsSetting Time Right Button Controls Changing Rolling Filter Timing To change the rolling-filter timingModel G0648 Rolling Filter Consumption Chart T20475-Second Layer Paper Filter Roll AccessoriesT20474-First Layer Stainless Screen T20529-Third Layer FilterSteel 6 Elbows H5297 6 Welding Fume Collection KitH7217-Rigid Flex Hose G7366 6 G7368 6 G7367 6 G7369 6 90G7370 6Model T20505 welding respirator H3157-Deluxe Welding GlovesSchedule MaintenanceCleaning LubricationLong-Term Storage Slag-Screen CleaningTo perform this procedure Tools Needed QtyRolling-Filter Replacement Removing recovery axlePage Vibrating Filter Manual Cleaning Page Page Hepa Filter Manual Cleaning To clean the Hepa filterPage Symptom Possible Cause Possible Solution ServiceTroubleshooting Operation Wiring Electrical Safety InstructionsWiring Overview 220 VACMain Electrical Box Wiring Main ELE BOXInput relay, fuse bus, phase Controller Transformer Pigtail Main Electrical Box ComponentsControl Panel WiringMAIN ELE Cntrl Control Panel Electrical Components DigitalCabinet Wiring MOTCabinet Electrical Components VibratingParts Main Parts BreakdownParts List DescriptionMotor 2HP 220V 3PH Blast Gates and Ducting Arm Breakdown Parts List Main Electrical Box Label Placement G0648 Welding Fume Extractor 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%