Grizzly G0648 owner manual Maintenance, Schedule, Lubrication, Cleaning

Page 27

SECTION 6: MAINTENANCE

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Always wear an OSHA approved respirator when clean- ing this machine.

Daily Check/Maintenance:

•Leaking seals or ducting.

•Worn or damaged power cord.

•Clean slag drawer screens.

•Empty dust drawer.

•Inspect and correct for any other unsafe condition.

Weekly Check/Maintenance:.

•Carefully wipe off any dust caked on the elec- tronic eye lens (see Figure 23 for location).

Monthly Check/Maintenance:

•Disconnect from power and vacuum and wipe out any dust buildup from the inside of the control box and filter cabinets. Do not use compressed air close to the filters or electri- cal components.

•Use a dry rag and wipe all drive chains and sprockets clean; then brush the chain links with a thin coat of light machine oil. Refer to Figure 23 for locations.

G0648 Welding Fume Extractor

Lubrication

Use a dry rag to wipe all drive chains and sprock- ets clean; then brush the chain links with a thin coat of light machine oil. Refer to Figure 23 for locations.

Electric

Eye

Oil Drive

Chains

Figure 23. Lubrication locations.

Cleaning

Cleaning the Model G0648 is relatively easy. Put on an OSHA approved respirator and vacuum excess dust, and wipe off the remaining dust with a damp cloth. Do not use harsh detergents or sol- vent on the cabinet, and never spray compressed air close to filters or electrical components.

-25-

Image 27

Contents Model G0648 Welding Fume Extractor Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Identification Vibrating Filter & Hepa Filter HousingMachine Data Sheet Other Specifications !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29# 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Additional Safety Instructions for Welding Fume Extractors Meeting Welding Fume Extraction Codes Standards Circuit Requirements 220V 3-Phase OperationUnpacking SetupSetup Safety Items Needed for SetupInventory Crate 1 Figure QtyBox 2 Figure Qty Hardware Recognition Chart Floor Load Site ConsiderationsTo test run the machine Ducting Arm InstallationTo install the ducting arm Test RunCompletely open both blast gates on the ducting arm Figure Operation Safety General Operation OperationsTo use the machine Page Setting Time Left Button Controls Setting Time Right Button ControlsControl Panel Operation To change the rolling-filter timing Changing Rolling Filter TimingModel G0648 Rolling Filter Consumption Chart T20529-Third Layer Filter AccessoriesT20474-First Layer Stainless Screen T20475-Second Layer Paper Filter RollG7366 6 G7368 6 G7367 6 G7369 6 90G7370 6 H5297 6 Welding Fume Collection KitH7217-Rigid Flex Hose Steel 6 ElbowsH3157-Deluxe Welding Gloves Model T20505 welding respiratorLubrication MaintenanceCleaning ScheduleTools Needed Qty Slag-Screen CleaningTo perform this procedure Long-Term StorageRemoving recovery axle Rolling-Filter ReplacementPage Vibrating Filter Manual Cleaning Page Page To clean the Hepa filter Hepa Filter Manual CleaningPage Service TroubleshootingSymptom Possible Cause Possible Solution Operation Electrical Safety Instructions Wiring220 VAC Wiring OverviewMain ELE BOX Main Electrical Box WiringMain Electrical Box Components Input relay, fuse bus, phase Controller Transformer PigtailControl Panel WiringMAIN ELE Cntrl Digital Control Panel Electrical ComponentsMOT Cabinet WiringVibrating Cabinet Electrical ComponentsMain Parts Breakdown PartsDescription Parts ListMotor 2HP 220V 3PH Blast Gates and Ducting Arm Breakdown Parts List Main Electrical Box Label Placement G0648 Welding Fume Extractor 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%