Grizzly G0648 owner manual Vibrating Filter Manual Cleaning

Page 31

Vibrating Filter

(Manual Cleaning)

The vibrating filter collects 85% of the 1-micron particles. This filter rarely needs to be replaced if the machine is used properly and the filter is periodically removed and manually cleaned.

Tools Needed	Qty
Wrench 17mm	1
Wrench 14mm	1
OSHA Approved Respirator	1
Safety Goggles	1
Air Compressor	1
Blowgun	1
To perform this procedure:

1.With the machine plugged in, press the manual cleaning mode and hold for a few seconds. The vibrating filter motor will operate, cleaning the vibrating filters.

2.DISCONNECT THE MACHINE FROM POWER, put on your respirator and safety goggles.

3.Unlatch the HEPA filter housing, open the housing, and lift the HEPA filter up and out of the housing (Figure 33).

Latch

Figure 33. Removing HEPA filter housing.

G0648 Welding Fume Extractor

4.Remove the plastic caps and loosen both jam nuts until they park against the underside of the spring retaining bolt heads (Figure 34).

Cap

Spring

Retaining

Bolt

Jam Nut

Figure 34. Vibrating filter retainer.

5.Using the 17mm wrench or a socket wrench, remove the right-side spring retaining bolt from the cabinet (Figure 33).

6.Reach into the cabinet, firmly grasp the right-side compression spring, and remove the spring (Figure 35). The spring is under tension, so make sure you do not lose your grip while you work the spring out of the cabinet.

Spring

Retaining

Bolt

Figure 35. Vibration motor access.

7.Repeat Steps 4–6on the left-hand retaining bolt and spring.

-29-

Image 31

Contents Model G0648 Welding Fume Extractor Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Identification Vibrating Filter & Hepa Filter HousingMachine Data Sheet Other Specifications !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29# 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Additional Safety Instructions for Welding Fume Extractors Meeting Welding Fume Extraction Codes Standards Circuit Requirements 220V 3-Phase OperationUnpacking SetupSetup Safety Items Needed for SetupCrate 1 Figure Qty InventoryBox 2 Figure Qty Hardware Recognition Chart Floor Load Site ConsiderationsTo test run the machine Ducting Arm InstallationTo install the ducting arm Test RunCompletely open both blast gates on the ducting arm Figure Operations Operation Safety General OperationTo use the machine Page Setting Time Right Button Controls Setting Time Left Button ControlsControl Panel Operation To change the rolling-filter timing Changing Rolling Filter TimingModel G0648 Rolling Filter Consumption Chart T20529-Third Layer Filter AccessoriesT20474-First Layer Stainless Screen T20475-Second Layer Paper Filter RollG7366 6 G7368 6 G7367 6 G7369 6 90G7370 6 H5297 6 Welding Fume Collection KitH7217-Rigid Flex Hose Steel 6 ElbowsH3157-Deluxe Welding Gloves Model T20505 welding respiratorLubrication MaintenanceCleaning ScheduleTools Needed Qty Slag-Screen CleaningTo perform this procedure Long-Term StorageRemoving recovery axle Rolling-Filter ReplacementPage Vibrating Filter Manual Cleaning Page Page To clean the Hepa filter Hepa Filter Manual CleaningPage Troubleshooting ServiceSymptom Possible Cause Possible Solution Operation Electrical Safety Instructions Wiring220 VAC Wiring OverviewMain ELE BOX Main Electrical Box WiringMain Electrical Box Components Input relay, fuse bus, phase Controller Transformer PigtailControl Panel WiringMAIN ELE Cntrl Digital Control Panel Electrical ComponentsMOT Cabinet WiringVibrating Cabinet Electrical ComponentsMain Parts Breakdown PartsDescription Parts ListMotor 2HP 220V 3PH Blast Gates and Ducting Arm Breakdown Parts List Main Electrical Box Label Placement G0648 Welding Fume Extractor 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%