Grizzly G0648 owner manual Wiring, Electrical Safety Instructions

Page 38

SECTION 8: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Study this diagram carefully. If you notice differences between your machine and these wiring diagrams, call Technical Support at (570) 546-9663 for assistance.

Electrical Safety Instructions

1.SHOCK HAZARD. Disconnect the power from the machine before servicing electri- cal components. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death.

2.CIRCUIT REQUIREMENTS. You MUST fol- low the CIRCUIT REQUIREMENTS section on Page 10. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared cir- cuit, consult a qualified electrician.

3.GROUNDED CIRCUIT. Electrocution or fire could result if the machine is not grounded and installed in compliance with electrical codes. Compliance MUST be verified by a qualified electrician.

4.MOTOR WIRING. The motor wiring shown in these diagrams are current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the motor junction box.

5.EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties under- standing the information included in this section, contact our Technical Support at (570) 546-9663.

NOTICE

The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com.

WARNING!

SHOCK HAZARD!

Disconnect power before working on wiring.

NOTICE

This machine uses sensitive electronics that rely on stable current on all power supply legs. We do not recommend connecting this machine to a phase converter. Ignoring this notice may void warranty.

-36-	G0648 Welding Fume Extractor

Image 38

Contents Model G0648 Welding Fume Extractor Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Vibrating Filter & Hepa Filter Housing IdentificationMachine Data Sheet Other Specifications !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Welding Fume Extractors Meeting Welding Fume Extraction Codes Standards 220V 3-Phase Operation Circuit RequirementsItems Needed for Setup SetupSetup Safety UnpackingBox 2 Figure Qty InventoryCrate 1 Figure Qty Hardware Recognition Chart Site Considerations Floor LoadTest Run Ducting Arm InstallationTo install the ducting arm To test run the machineCompletely open both blast gates on the ducting arm Figure To use the machine Operation Safety General OperationOperations Page Control Panel Operation Setting Time Left Button ControlsSetting Time Right Button Controls Changing Rolling Filter Timing To change the rolling-filter timingModel G0648 Rolling Filter Consumption Chart T20475-Second Layer Paper Filter Roll AccessoriesT20474-First Layer Stainless Screen T20529-Third Layer FilterSteel 6 Elbows H5297 6 Welding Fume Collection KitH7217-Rigid Flex Hose G7366 6 G7368 6 G7367 6 G7369 6 90G7370 6Model T20505 welding respirator H3157-Deluxe Welding GlovesSchedule MaintenanceCleaning LubricationLong-Term Storage Slag-Screen CleaningTo perform this procedure Tools Needed QtyRolling-Filter Replacement Removing recovery axlePage Vibrating Filter Manual Cleaning Page Page Hepa Filter Manual Cleaning To clean the Hepa filterPage Symptom Possible Cause Possible Solution ServiceTroubleshooting Operation Wiring Electrical Safety InstructionsWiring Overview 220 VACMain Electrical Box Wiring Main ELE BOXInput relay, fuse bus, phase Controller Transformer Pigtail Main Electrical Box ComponentsControl Panel WiringMAIN ELE Cntrl Control Panel Electrical Components DigitalCabinet Wiring MOTCabinet Electrical Components VibratingParts Main Parts BreakdownParts List DescriptionMotor 2HP 220V 3PH Blast Gates and Ducting Arm Breakdown Parts List Main Electrical Box Label Placement G0648 Welding Fume Extractor 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%