Grizzly G0648 owner manual Control Panel Operation, Setting Time Left Button Controls

Page 21

Control Panel Operation

A.EXHAUSTING TIME (min): Displays, in min- utes, how much welding time is allotted before new filter paper is exposed.

B.FILTER ROLLING TIME (sec): Displays, in seconds, the duration of roller-filter advance.

C.FILTER CLEANING: Lamp lights when the vibrating-type filter is being de-caked.

D.FILTER ROLLING: Lamp lights when the roller-type filter advances.

E.OUT OF FILTER: Lamp lights when the roller-type filter has run out and needs chang- ing.

F.OPERATING: Lamp lights when the machine is running.

G.SETTING TIME (Left Button): Controls the

EXHAUSTING TIME.

H.SETTING TIME (Right Button): Controls the

FILTER ROLLING TIME.

I.CLEANING FILTER (MANUAL MODE)

Button: When the machine is OFF, press this button to start the vibrating motor and de-cake the pleated filter.

J.ON/OFF Button: Toggles machine operation between ON and OFF.

K.DOOR LATCH: Allows access to the control panel electrical system.

L.EMERGENCY STOP Button: Shuts down the machine in the event of an emergency.

M.FILTER INDICATOR Buzzer/Lamp: Lights and sounds when the roller-type filter has run out of paper.

N.FILTER INDICATOR Lamp: Lights when the vibrating filter needs to be cleaned or replaced.

O.FILTER INDICATOR Lamp: Lights when the HEPA filter needs to be cleaned or replaced.

		C	D	E	F
A	B
G	H	I		J
		I		J
		M			O
					O
K	L			N

Figure 9. Controls.

G0648 Welding Fume Extractor

-19-

Image 21

Contents Model G0648 Welding Fume Extractor Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Identification Vibrating Filter & Hepa Filter HousingMachine Data Sheet Other Specifications !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Welding Fume Extractors Meeting Welding Fume Extraction Codes Standards Circuit Requirements 220V 3-Phase OperationSetup Safety SetupItems Needed for Setup UnpackingInventory Crate 1 Figure QtyBox 2 Figure Qty Hardware Recognition Chart Floor Load Site ConsiderationsTo install the ducting arm Ducting Arm InstallationTest Run To test run the machineCompletely open both blast gates on the ducting arm Figure Operation Safety General Operation OperationsTo use the machine Page Setting Time Left Button Controls Setting Time Right Button ControlsControl Panel Operation To change the rolling-filter timing Changing Rolling Filter TimingModel G0648 Rolling Filter Consumption Chart T20474-First Layer Stainless Screen AccessoriesT20475-Second Layer Paper Filter Roll T20529-Third Layer FilterH7217-Rigid Flex Hose H5297 6 Welding Fume Collection KitSteel 6 Elbows G7366 6 G7368 6 G7367 6 G7369 6 90G7370 6H3157-Deluxe Welding Gloves Model T20505 welding respiratorCleaning MaintenanceSchedule LubricationTo perform this procedure Slag-Screen CleaningLong-Term Storage Tools Needed QtyRemoving recovery axle Rolling-Filter ReplacementPage Vibrating Filter Manual Cleaning Page Page To clean the Hepa filter Hepa Filter Manual CleaningPage Service TroubleshootingSymptom Possible Cause Possible Solution Operation Electrical Safety Instructions Wiring220 VAC Wiring OverviewMain ELE BOX Main Electrical Box WiringMain Electrical Box Components Input relay, fuse bus, phase Controller Transformer PigtailControl Panel WiringMAIN ELE Cntrl Digital Control Panel Electrical ComponentsMOT Cabinet WiringVibrating Cabinet Electrical ComponentsMain Parts Breakdown PartsDescription Parts ListMotor 2HP 220V 3PH Blast Gates and Ducting Arm Breakdown Parts List Main Electrical Box Label Placement G0648 Welding Fume Extractor 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%