Grizzly G0648 owner manual Circuit Requirements, 220V 3-Phase Operation

Page 12

SECTION 2: CIRCUIT REQUIREMENTS

220V 3-Phase

Operation

Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual.

Electrocution or fire could result if machine is not grounded and installed in compliance with electrical codes. Compliance MUST be verified by a qualified electrician!

Full Load Amperage Draw

Amp Draw at 220V 3-Phase

6.23 Amps

Power Supply Circuit Requirements

You MUST connect your machine to a grounded circuit that is rated for the amperage given below. Never replace a circuit breaker on an existing cir- cuit with one of higher amperage without consult- ing a qualified electrician to ensure compliance with wiring codes. If you are unsure about the wiring codes in your area or you plan to con- nect your machine to a shared circuit, consult a qualified electrician.

Minimum Circuit Size (220V 3-Phase)... 15 Amps

Power Connection

The power connection device depends on the type of installed or planned service. We recom- mend using a NEMA15-15 plug and receptacle shown in Figure 2.

<gdjcYZY

DjiaZi7dm

8jggZci

8Vggn^c\

7aVYZh

<gdjcY^c\E^c

Figure 2. NEMA 15-15 plug and receptacle.

Extension Cords

Using extension cords may reduce the life of the motor. Instead, place the machine near a power source. If you must use an extension cord:

•Use at least a 14 gauge cord that does not exceed 4 meters in length.

•Ensure that the extension cord contains a ground wire and plug pin.

NOTICE

This machine uses sensitive electronics that rely on stable current on all power supply legs. We do not recommend connecting this machine to a phase converter. Ignoring this notice may void warranty.

-10-	READ ELECTRICAL SAFETY	G0648 Welding Fume Extractor
	ON PAGE 36!

Image 12

Contents Model G0648 Welding Fume Extractor Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Foreword Functional OverviewContact Info Vibrating Filter & Hepa Filter Housing IdentificationMachine Data Sheet Other Specifications !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Welding Fume Extractors Meeting Welding Fume Extraction Codes Standards 220V 3-Phase Operation Circuit RequirementsSetup Setup SafetyItems Needed for Setup UnpackingInventory Crate 1 Figure QtyBox 2 Figure Qty Hardware Recognition Chart Site Considerations Floor LoadDucting Arm Installation To install the ducting armTest Run To test run the machineCompletely open both blast gates on the ducting arm Figure Operation Safety General Operation OperationsTo use the machine Page Setting Time Left Button Controls Setting Time Right Button ControlsControl Panel Operation Changing Rolling Filter Timing To change the rolling-filter timingModel G0648 Rolling Filter Consumption Chart Accessories T20474-First Layer Stainless ScreenT20475-Second Layer Paper Filter Roll T20529-Third Layer FilterH5297 6 Welding Fume Collection Kit H7217-Rigid Flex HoseSteel 6 Elbows G7366 6 G7368 6 G7367 6 G7369 6 90G7370 6Model T20505 welding respirator H3157-Deluxe Welding GlovesMaintenance CleaningSchedule LubricationSlag-Screen Cleaning To perform this procedureLong-Term Storage Tools Needed QtyRolling-Filter Replacement Removing recovery axlePage Vibrating Filter Manual Cleaning Page Page Hepa Filter Manual Cleaning To clean the Hepa filterPage Service TroubleshootingSymptom Possible Cause Possible Solution Operation Wiring Electrical Safety InstructionsWiring Overview 220 VACMain Electrical Box Wiring Main ELE BOXInput relay, fuse bus, phase Controller Transformer Pigtail Main Electrical Box ComponentsControl Panel WiringMAIN ELE Cntrl Control Panel Electrical Components DigitalCabinet Wiring MOTCabinet Electrical Components VibratingParts Main Parts BreakdownParts List DescriptionMotor 2HP 220V 3PH Blast Gates and Ducting Arm Breakdown Parts List Main Electrical Box Label Placement G0648 Welding Fume Extractor 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%