Woodstock W1730 manual Electrical, Circuit Requirements, Circuit Type, Nema

Page 10

W1730 Oscillating Edge Sander

ELECTRICAL

SETUP

Circuit Requirements

This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power.

A power supply circuit includes all electrical equipment between the breaker box or fuse panel in the building and the machine. The power supply circuit used for this machine must be sized to safely handle the full- load current drawn from the machine for an extended period of time. (If this machine is connected to a circuit protected by fuses, use a time delay fuse marked D.)

Full-Load Current Rating

The full-load current rating is the amperage a machine draws at 100% of the rated output power. On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations.

Full-Load Current Rating at 240V

9 Amps

The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do later in this manual.

Incorrectly wiring or grounding this machine can cause electrocution, fire, or machine damage. To reduce this risk, only a qualified electrician or service personnel should do any required electrical work for this machine.

Circuit Requirements for 240V

This machine is prewired to operate on a 220V power supply circuit that has a verified ground and meets the following requirements:

Circuit Type

220V/240V, 60 Hz, Single-Phase

Circuit Size

15 Amps

Plug/Receptacle

NEMA 6-15

NOTICE

The circuit requirements listed in this manual apply to a dedicated circuit— where only one machine will be running at a time. If this machine will be connected to a shared circuit where multiple machines will be running at the same time, consult a qualified electrician to ensure that the circuit is properly sized for safe operation.

-8-

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Oscillating Edge Sander Page Table of Contents Woodstock Technical Support IntroductionAbout Your New W1730 Oscillating Edge Sander Controls and Features IntroductionSafety Standard Machinery Safety InstructionsSafety Additional Safety for Oscillating Edge Sanders Avoiding Potential Injuries Do not sand wood with fingers close To spindleCircuit Type ElectricalCircuit Requirements NemaGrounding Requirements Extension CordsUnpacking SET UPItems Needed for Set Up DescriptionBox Contents Figure InventoryMachine Placement Cleaning Machine Backstop To install the belt, do these stepsSanding Belt To mount the back stop, do these stepsDust Port Door Dust PortDust Port Cover To install the sanding spindle, do these steps Sanding SpindleTest Run Dust CollectionGear Box To check and refill the gear box, do these stepsUnplug the sander To adjust the sanding belt tracking, do these stepsBelt Tracking ­ If the belt is not tracking correctly, repeat StepsBelt Grits OperationsGeneral Emergency Stop ButtonTo adjust the platen angle, do these steps Platen Angle AdjustmentTable Adjustment To vertically adjust the table, do these stepsFence To adjust the miter gauge, do these stepsMiter Gauge Spindle Table HeightTo perform spindle sanding operations, do these steps Spindle SandingEnd & Edge Sanding To perform an edge or end sanding operation, do these stepsCleaning MaintenanceTable & Base Lubrication To grease the rack and pinion gear, do these stepsSpindle Connector EccentricEvery 6-8 Hours of Running Time Maintenance ScheduleMaintenance Notes Every 2,000 hoursCalibrating Angle Gauge To calibrate the angle gauge, do these stepsRemoving Drive Roller To remove the drive roller, do these stepsW1730 Wiring Diagram Troubleshooting Symptom Possible CauseDuring operation Adjustment 195 194 151 188 164 193 190 150 187 163 183 186 Breakdown Parts Breakdown DescriptionGear BOX Cover Warranty Regristration Woodstock international inc. p.o. box Bellingham, wa Warranty High Quality Machines and Tools
Top Page Image Contents