Woodstock W1730 manual Warranty

Page 39

WARRANTY

Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work- manship and materials for a period of 2 years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or to repairs or alterations made or specifically authorized by anyone other than Woodstock International, Inc.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX® machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facility designated by our Bellingham, WA office, with proof of their purchase of the product within 2 years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products.

Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabil- ity standards. We reserve the right to change specifications at any time because of our commitment to continuously improve the quality of our products.

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Oscillating Edge Sander Page Table of Contents Introduction Woodstock Technical SupportAbout Your New W1730 Oscillating Edge Sander Introduction Controls and FeaturesStandard Machinery Safety Instructions SafetySafety Additional Safety for Oscillating Edge Sanders Do not sand wood with fingers close To spindle Avoiding Potential InjuriesNema ElectricalCircuit Requirements Circuit TypeExtension Cords Grounding RequirementsDescription SET UPItems Needed for Set Up UnpackingInventory Box Contents FigureMachine Placement Cleaning Machine To mount the back stop, do these steps To install the belt, do these stepsSanding Belt BackstopDust Port Dust Port DoorDust Port Cover Sanding Spindle To install the sanding spindle, do these stepsTo check and refill the gear box, do these steps Dust CollectionGear Box Test Run­ If the belt is not tracking correctly, repeat Steps To adjust the sanding belt tracking, do these stepsBelt Tracking Unplug the sanderEmergency Stop Button OperationsGeneral Belt GritsTo vertically adjust the table, do these steps Platen Angle AdjustmentTable Adjustment To adjust the platen angle, do these stepsSpindle Table Height To adjust the miter gauge, do these stepsMiter Gauge FenceTo perform an edge or end sanding operation, do these steps Spindle SandingEnd & Edge Sanding To perform spindle sanding operations, do these stepsMaintenance CleaningTable & Base To grease the rack and pinion gear, do these steps LubricationEccentric Spindle ConnectorEvery 2,000 hours Maintenance ScheduleMaintenance Notes Every 6-8 Hours of Running TimeTo calibrate the angle gauge, do these steps Calibrating Angle GaugeTo remove the drive roller, do these steps Removing Drive RollerW1730 Wiring Diagram Symptom Possible Cause TroubleshootingDuring operation Adjustment 195 194 151 188 164 193 190 150 187 163 183 186 Breakdown Description Parts BreakdownGear BOX Cover Warranty Regristration Woodstock international inc. p.o. box Bellingham, wa Warranty High Quality Machines and Tools
Top Page Image Contents