Woodstock W1730 manual Sanding Spindle, To install the sanding spindle, do these steps

Page 17

W1730 Oscillating Edge Sander

Sanding Spindle

The Model W1730 comes with a spindle sanding attachment for sanding curved surfaces. The included sanding drums measure 1-1/2", 2", and 3" in diameter. The spindle table may also be used on the end of the sanding belt if so desired. Be sure to periodically adjust the table height to minimize spot wear on the spindle/belt.

To install the sanding spindle, do these steps:

1.Release the dust port cover latch, open the cover, then latch the cover to the belt access door.

2.Remove the three cap screws and false cover from the sanding belt drum.

3.Line up the screw holes and place the spindle into the sanding belt drum.

4.Thread the cap screws removed in Step 2 into the sanding belt drum and tighten evenly and securely as shown in Figure 17.

5.Slide a sanding drum onto the spindle, and insert the 5/16" spindle washer and 5/16-18 x 1/2 hex bolt into the top of the spindle.

6.Insert the rod into the side of the spindle to anchor it and tighten the hex bolt as shown in Figure 18.

7.Insert the spindle table assembly shaft into the opening in the idler roller bracket as shown in

Figure 19.

8.Thread the table lock handle into the pre-tapped hole in the idler roller bracket. Note:­ The handle is spring loaded and can be used as a ratchet.

9.Remove the installed table insert by removing the three flat head screws in the insert.

10.Replace with the table insert that matches the sanding drum diameter. Tighten with the flat head screws removed in Step 9.

Figure 17. Securing the cap screws.

Figure 18. Anchoring the spindle with the

rod.

SETUP

Figure 19. Inserting spindle table assembly into idler roller bracket.

-15-

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Oscillating Edge Sander Page Table of Contents About Your New W1730 Oscillating Edge Sander IntroductionWoodstock Technical Support Introduction Controls and FeaturesStandard Machinery Safety Instructions SafetySafety Additional Safety for Oscillating Edge Sanders Do not sand wood with fingers close To spindle Avoiding Potential InjuriesCircuit Requirements ElectricalCircuit Type NemaExtension Cords Grounding RequirementsItems Needed for Set Up SET UPUnpacking DescriptionInventory Box Contents FigureMachine Placement Cleaning Machine Sanding Belt To install the belt, do these stepsBackstop To mount the back stop, do these stepsDust Port Cover Dust PortDust Port Door Sanding Spindle To install the sanding spindle, do these stepsGear Box Dust CollectionTest Run To check and refill the gear box, do these stepsBelt Tracking To adjust the sanding belt tracking, do these stepsUnplug the sander ­ If the belt is not tracking correctly, repeat StepsGeneral OperationsBelt Grits Emergency Stop ButtonTable Adjustment Platen Angle AdjustmentTo adjust the platen angle, do these steps To vertically adjust the table, do these stepsMiter Gauge To adjust the miter gauge, do these stepsFence Spindle Table HeightEnd & Edge Sanding Spindle SandingTo perform spindle sanding operations, do these steps To perform an edge or end sanding operation, do these stepsTable & Base MaintenanceCleaning To grease the rack and pinion gear, do these steps LubricationEccentric Spindle ConnectorMaintenance Notes Maintenance ScheduleEvery 6-8 Hours of Running Time Every 2,000 hoursTo calibrate the angle gauge, do these steps Calibrating Angle GaugeTo remove the drive roller, do these steps Removing Drive RollerW1730 Wiring Diagram Symptom Possible Cause TroubleshootingDuring operation Adjustment 195 194 151 188 164 193 190 150 187 163 183 186 Breakdown Description Parts BreakdownGear BOX Cover Warranty Regristration Woodstock international inc. p.o. box Bellingham, wa Warranty High Quality Machines and Tools
Top Page Image Contents