Woodstock W1730 manual Inventory, Box Contents Figure

Page 13

W1730 Oscillating Edge Sander

Inventory

The following is a description of the main components shipped with the SHOP FOX® Model W1730. Lay the components out to inventory them.

Box Contents (Figure 9):
A.	Fence	1
B.	Spindle Table Assembly	1

G

HC

B

C.	Sanding Belt	1
D.	Miter Gauge	1
E.	Dust Port	1
F.	Back Stop	1
G.	Dust Port Cover	1
H.	Dust Port Door	1
Box Contents Continued (Figure 10):
I.	3" Drum	1
J.	2" Drum	1

E

D

A

F

Figure 9. Box contents.

SETUP

K.	1-1/2" Drum		1
L.	3" Table Insert		1
M.	2" Table Insert		1
N.	1-1/2" Table Insert		1
O.	Spindle		1
P.	Hardware Bag		1
	•	Lock Handle	1
	•	Star Knob 5/16-18 x 1	2
	•	Hex Bolt 5/16-18 x 1	2
	•	Hex Bolt 5/16-18 x 1/2	1
	•	Phillips Head Screw 1/4-20 x 3/8"	4
	•	Spindle Washer 5/16	1
	•	Flat Washer 5/16	4

I

O

P

J

K

N

M

L

• Hinge Pin	4
• Open End Wrench 10mm x 12mm	1
• Hex Wrench 5mm	1
• Hex Wrench 6mm	1
• Rod	1
• Drive Puller Plate	1
• Cap Screw 5/16-18 x 1-1/4	1
• Cap Screw 1/4-20 x 1-3/4	2

If any parts appear to be missing, examine the packaging carefully. If any parts are missing, find the part number in the back of this manual and contact Woodstock International, Inc. at 360-734-3482 or at tech-support@ shopfox.biz

Figure 10. Box contents continued.

NOTICE

When ordering replacement parts, refer to the parts list and diagram in the back of the manual.

SUFFOCATION HAZARD! Immediately discard all plastic bags and pack- ing materials to elimi- nate choking/suffocation hazards for children and animals.

-11-

Image 13

Contents Oscillating Edge Sander Page Table of Contents Woodstock Technical Support IntroductionAbout Your New W1730 Oscillating Edge Sander Introduction Controls and FeaturesStandard Machinery Safety Instructions SafetySafety Additional Safety for Oscillating Edge Sanders Do not sand wood with fingers close To spindle Avoiding Potential InjuriesCircuit Requirements ElectricalCircuit Type NemaExtension Cords Grounding RequirementsItems Needed for Set Up SET UPUnpacking DescriptionInventory Box Contents FigureMachine Placement Cleaning Machine Sanding Belt To install the belt, do these stepsBackstop To mount the back stop, do these stepsDust Port Door Dust PortDust Port Cover Sanding Spindle To install the sanding spindle, do these stepsGear Box Dust CollectionTest Run To check and refill the gear box, do these stepsBelt Tracking To adjust the sanding belt tracking, do these stepsUnplug the sander If the belt is not tracking correctly, repeat StepsGeneral OperationsBelt Grits Emergency Stop ButtonTable Adjustment Platen Angle AdjustmentTo adjust the platen angle, do these steps To vertically adjust the table, do these stepsMiter Gauge To adjust the miter gauge, do these stepsFence Spindle Table HeightEnd & Edge Sanding Spindle SandingTo perform spindle sanding operations, do these steps To perform an edge or end sanding operation, do these stepsCleaning MaintenanceTable & Base To grease the rack and pinion gear, do these steps LubricationEccentric Spindle ConnectorMaintenance Notes Maintenance ScheduleEvery 6-8 Hours of Running Time Every 2,000 hoursTo calibrate the angle gauge, do these steps Calibrating Angle GaugeTo remove the drive roller, do these steps Removing Drive RollerW1730 Wiring Diagram Symptom Possible Cause TroubleshootingDuring operation Adjustment 195 194 151 188 164 193 190 150 187 163 183 186 Breakdown Description Parts BreakdownGear BOX Cover Warranty Regristration Woodstock international inc. p.o. box Bellingham, wa Warranty High Quality Machines and Tools