RIDGID TS3660 manual Features, Product Specifications, RIP Fence, Bevel Scale

Page 12

FEATURES

PRODUCT SPECIFICATIONS

Blade Diameter	10 in.
Blade Arbor	5/8 in.
Cutting Depth at 0°	3-3/8 in.
Cutting Depth at 45°	2-1/4 in.

Rating	120 V, AC Only, 60 Hz, 13	Amps
	240 V, AC Only, 60 Hz, 6.5	Amps
No Load Speed	3,450 r/min. (RPM)

		BEVEL
		LOCK
		LEVER
ANTI-KICKBACK			BEVEL
PAWLS			BEVEL
PAWLS			ADJUSTING
SEPARATOR	BLADE GUARD	SAW	HANDWHEEL
SEPARATOR	BLADE GUARD
(SPLITTER)	ASSEMBLY
(SPLITTER)	ASSEMBLY	BLADE
		BLADE
		RIP FENCE
			FRONT
MITER			RAIL
MITER
GAUGE		SWITCH
		SWITCH	LOCKING
		ASSEMBLY	LEVER
RIP FENCE		BEVEL SCALE
STORAGE		MITER GAUGE
HOOKS		MITER GAUGE
		STORAGE HOOK

LEG
STAND	HEIGHT
	ADJUSTING
	HANDWHEEL

BLADE HEIGHT

LOCK KNOB

HERC-U-LIFT™

LEVELING

FOOT

MOBILE BASE

Fig. 6

Image 12

Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Blade Coasts After Being Turned OFF  Never Operate the SAW on the FloorSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Authorized Service Center for repair. When servicSpeed and Wiring ElectricalExtension Cords Electrical ConnectionChanging Motor Voltage See Figures 2Junction BOX Manual Reset Button Motor Thermal Overload ProtectorSee Figure Glossary of Terms Features Product SpecificationsRIP Fence Bevel ScaleKnow Your Table SAW OverviewTools Needed HEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16Square Framing Square Loose Parts Key Description QtyLoose Parts List Assembly UnpackingMounting Holes To Assemble LEG Stand and Storage Brackets To Install Extension Tables To Mount the Table SAW to the LEG StandScrew With Washer To Install the HERC-U-LIFT Mobile Base to the LEG Stand To Install Bevel Adjusting HAND- Wheel To Install Height Adjusting HAND- WheelLock Blade Tube Height Lock Knob Adjusting Handwheel To assemble the Herc-U-Lift to the leg standTo Store Accessories To Install Front and Back RailsTool Storage Square Head Bolt Square Head BoltTo Adjust Front and Back Rails See Figures 23Front Rail Rear Shims To Install RIP Fence To Check the Throat PlateSET Screws RIP Fence in Locked Position Unlocked Position See Figures 27To Install Spacer BAR To Install Blade Guard AssemblyTo Align Blade Guard Assembly to the Blade To Mount Motor Assembly To Install the Belt GuardTo Install Belt Motor AssemblyTo Install Switch Assembly To Install END CapsTo Secure the Electrical Cords To Adjust Blade Depth To Adjust Blade AngleOperation HOW to Make a Featherboard FeatherboardPush Sticks Push Blocks See Figures 41Types of Cuts Cutting TipsCross CUT To USE the IND-I-CUT Feature To USE the HERC-U-LIFT Mobile Base to Move the Table SAWUnlock Pedal Metal Platform To USE the MICRO-ADJUST Feature on the RIP Fence MICRO-ADJUST Wheel Dust ChuteTo USE the SAW Dust Chute See Figures 46Switch KEY Removed Switch on To Make a Cross CUTSee Figures 49 To Make a RIP CUT To Make a Miter CUTTo Make a Bevel Cross CUT To Make a Bevel RIP CUTViewed from the FRONT, below the Table SAW To TightenTo Make a Compound Bevel Miter CUT Bevel RIP CUT Blade AngledScale RIP Fence To Make a Large Panel CUT To Make a NON-THROUGH CUT NON-THROUGH CUTTo Make a Dado CUT Dado CUTAdjustments To Install Zero Clearance Throat PlateTo REMOVE/REPLACE the Throat Plate Removing Throat Plate Zero ClearanceTo Replace the SAW Blade See Figures 62Blade Wrench Washer NUT Framing Square Heeling Paralleling the Blade to the Miter Gauge Groove See Figures 64Trunnion Bolt Trunnion Bolt LeverTo SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚ See Figures 67Screws Bevel Lock Lever Blade AT 90˚ Position To Adjust the Bevel Adjusting HAND- Wheel To Adjust the Miter GaugeTo Align and Adjust the RIP Fence Locking Lever HEX Head Screws Adjusting NUT Back RailSee Figures 74 To Adjust the RIP Fence Indicator PAN Head ScrewMaintenance AccessoriesGeneral Maintenance LubricationTroubleshooting Problem CauseSolution Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model No TS3660 Serial No

FEATURES

PRODUCT SPECIFICATIONS

3,450 r/min. (RPM)

RIP FENCE

BEVEL SCALE