RIDGID TS3660 manual Loose Parts, Key Description Qty

Page 15

LOOSE PARTS

9	8
9
16	15

Fig. 8

Key
No.	Description	Qty.
1	Miter Gauge	1
2	Guard Support Assembly	1
3	Blade Guard Assembly	1
4	Blade Wrench	2
5	Rip Fence	1
6	Bevel Adjusting Handwheel	1
7	Height Adjusting Handwheel	1
8	Back End Cap (left and right)	2
9	Front Rail	1

Key
No.	Description	Qty.
10	Back Rail	1
11	Table Extension	2
12	Motor	1
13	Belt Guard	1
14	Belt	1
15	Spacer Bar	1
16	Front End Cap (left and right)	2
17	Blister Hardware Pack
	(contents noted on blister pack) - not shown	1

Image 15

Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Never Operate the SAW on the Floor Specific Safety Rules Before Making a CUT, be Sure ALL ADJUST- Ments are Secure  Blade Coasts After Being Turned OFFSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsAuthorized Service Center for repair. When servic ServiceElectrical Connection Speed and WiringElectrical Extension CordsSee Figures 2 Changing Motor VoltageJunction BOX Manual Reset Button Motor Thermal Overload ProtectorSee Figure Glossary of Terms Bevel Scale FeaturesProduct Specifications RIP FenceOverview Know Your Table SAWTools Needed HEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16Square Framing Square Key Description Qty Loose PartsLoose Parts List Assembly UnpackingMounting Holes To Assemble LEG Stand and Storage Brackets To Install Extension Tables To Mount the Table SAW to the LEG StandScrew With Washer To Install the HERC-U-LIFT Mobile Base to the LEG Stand To assemble the Herc-U-Lift to the leg stand To Install Bevel Adjusting HAND- WheelTo Install Height Adjusting HAND- Wheel Lock Blade Tube Height Lock Knob Adjusting HandwheelSquare Head Bolt To Store AccessoriesTo Install Front and Back Rails Tool Storage Square Head BoltTo Adjust Front and Back Rails See Figures 23Front Rail Rear Shims See Figures 27 To Install RIP FenceTo Check the Throat Plate SET Screws RIP Fence in Locked Position Unlocked PositionTo Install Spacer BAR To Install Blade Guard AssemblyTo Align Blade Guard Assembly to the Blade Motor Assembly To Mount Motor AssemblyTo Install the Belt Guard To Install BeltTo Install Switch Assembly To Install END CapsTo Secure the Electrical Cords To Adjust Blade Angle To Adjust Blade DepthOperation See Figures 41 HOW to Make a FeatherboardFeatherboard Push Sticks Push BlocksTypes of Cuts Cutting TipsCross CUT To USE the IND-I-CUT Feature To USE the HERC-U-LIFT Mobile Base to Move the Table SAWUnlock Pedal Metal Platform See Figures 46 To USE the MICRO-ADJUST Feature on the RIP FenceMICRO-ADJUST Wheel Dust Chute To USE the SAW Dust ChuteSwitch KEY Removed Switch on To Make a Cross CUTSee Figures 49 To Make a Miter CUT To Make a RIP CUTTo Tighten To Make a Bevel Cross CUTTo Make a Bevel RIP CUT Viewed from the FRONT, below the Table SAWTo Make a Compound Bevel Miter CUT Bevel RIP CUT Blade AngledScale RIP Fence To Make a Large Panel CUT NON-THROUGH CUT To Make a NON-THROUGH CUTDado CUT To Make a Dado CUTRemoving Throat Plate Zero Clearance AdjustmentsTo Install Zero Clearance Throat Plate To REMOVE/REPLACE the Throat PlateTo Replace the SAW Blade See Figures 62Blade Wrench Washer NUT Framing Square Trunnion Bolt Lever Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 64 Trunnion BoltTo SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚ See Figures 67Screws Bevel Lock Lever Blade AT 90˚ Position To Adjust the Miter Gauge To Adjust the Bevel Adjusting HAND- WheelTo Align and Adjust the RIP Fence Locking Lever HEX Head Screws Adjusting NUT Back RailSee Figures 74 PAN Head Screw To Adjust the RIP Fence IndicatorLubrication MaintenanceAccessories General MaintenanceProblem Cause TroubleshootingSolution HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No TS3660 Serial No Customer Service Information

LOOSE PARTS

Key

Description

Qty.