RIDGID TS3660 manual Warranty, DAY Satisfaction Guarantee Policy, Additional Limitations

Page 51

WARRANTY

RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY

Proof of purchase must be presented when requesting war- ranty service.

Limited to RIDGID® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.

90-DAY SATISFACTION GUARANTEE POLICY

During the first 90 days after the date of purchase, if you are dissatisfied with the performance of this RIDGID® Hand Held and Stationary Power Tool for any reason you may return the tool to the dealer from which it was purchased for a full refund or exchange. To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product. The replacement tool will be covered by the limited warranty for the balance of the 3 YEAR service warranty period.

WHAT IS COVERED UNDER THE 3 YEAR LIMITED SERVICE WARRANTY

This warranty on RIDGID® Hand Held and Stationary Power Tools covers all defects in workmanship or materials and nor- mal wear items such as brushes, chucks, motors, switches, cords, gears and even cordless batteries in this RIDGID® tool for three years following the purchase date of the tool. Warranties for other RIDGID® products may vary.

HOW TO OBTAIN SERVICE

To obtain service for this RIDGID® tool you must return it; freight prepaid, or take it in to an authorized service center for RIDGID® branded hand held and stationary power tools. You may obtain the location of the authorized service center nearest you by calling (toll free) 1-866-539-1710 or by log- ging on to the RIDGID® website at www.ridgid.com. When requesting warranty service, you must present the original dated sales receipt. The authorized service center will re- pair any faulty workmanship, and either repair or replace any part covered under the warranty, at our option, at no charge to you.

WHAT IS NOT COVERED

This warranty applies only to the original purchaser at retail and may not be transferred. This warranty only covers de- fects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by other than an authorized service center for RIDGID® branded hand held and stationary power tools. Consumable accessories pro- vided with the tool such as, but not limited to, blades, bits and sand paper are not covered.

RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC. MAKE NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI- CALLY STATED IN THIS WARRANTY.

ADDITIONAL LIMITATIONS

To the extent permitted by applicable law, all implied war- ranties, including warranties of MERCHANTABILITY or FIT- NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase. One World Technologies, Inc. and RIDGID, Inc. are not responsible for direct, indirect, incidental or conse- quential damages. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential dam- ages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also

One World Technologies, Inc.

Hwy. 8

Pickens, SC 29671

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Never Operate the SAW on the Floor Specific Safety Rules Before Making a CUT, be Sure ALL ADJUST- Ments are Secure  Blade Coasts After Being Turned OFFSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsAuthorized Service Center for repair. When servic ServiceElectrical Connection Speed and WiringElectrical Extension CordsSee Figures 2 Changing Motor VoltageJunction BOX Manual Reset Button Motor Thermal Overload ProtectorSee Figure Glossary of Terms Bevel Scale FeaturesProduct Specifications RIP FenceOverview Know Your Table SAWTools Needed HEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16Square Framing Square Key Description Qty Loose PartsLoose Parts List Assembly UnpackingMounting Holes To Assemble LEG Stand and Storage Brackets To Install Extension Tables To Mount the Table SAW to the LEG StandScrew With Washer To Install the HERC-U-LIFT Mobile Base to the LEG Stand To assemble the Herc-U-Lift to the leg stand To Install Bevel Adjusting HAND- WheelTo Install Height Adjusting HAND- Wheel Lock Blade Tube Height Lock Knob Adjusting HandwheelSquare Head Bolt To Store AccessoriesTo Install Front and Back Rails Tool Storage Square Head BoltTo Adjust Front and Back Rails See Figures 23Front Rail Rear Shims See Figures 27 To Install RIP FenceTo Check the Throat Plate SET Screws RIP Fence in Locked Position Unlocked PositionTo Install Spacer BAR To Install Blade Guard AssemblyTo Align Blade Guard Assembly to the Blade Motor Assembly To Mount Motor AssemblyTo Install the Belt Guard To Install BeltTo Install Switch Assembly To Install END CapsTo Secure the Electrical Cords To Adjust Blade Angle To Adjust Blade DepthOperation See Figures 41 HOW to Make a FeatherboardFeatherboard Push Sticks Push BlocksTypes of Cuts Cutting TipsCross CUT To USE the IND-I-CUT Feature To USE the HERC-U-LIFT Mobile Base to Move the Table SAWUnlock Pedal Metal Platform See Figures 46 To USE the MICRO-ADJUST Feature on the RIP FenceMICRO-ADJUST Wheel Dust Chute To USE the SAW Dust ChuteSwitch KEY Removed Switch on To Make a Cross CUTSee Figures 49 To Make a Miter CUT To Make a RIP CUTTo Tighten To Make a Bevel Cross CUTTo Make a Bevel RIP CUT Viewed from the FRONT, below the Table SAWTo Make a Compound Bevel Miter CUT Bevel RIP CUT Blade AngledScale RIP Fence To Make a Large Panel CUT NON-THROUGH CUT To Make a NON-THROUGH CUTDado CUT To Make a Dado CUTRemoving Throat Plate Zero Clearance AdjustmentsTo Install Zero Clearance Throat Plate To REMOVE/REPLACE the Throat PlateTo Replace the SAW Blade See Figures 62Blade Wrench Washer NUT Framing Square Trunnion Bolt Lever Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 64 Trunnion BoltTo SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚ See Figures 67Screws Bevel Lock Lever Blade AT 90˚ Position To Adjust the Miter Gauge To Adjust the Bevel Adjusting HAND- WheelTo Align and Adjust the RIP Fence Locking Lever HEX Head Screws Adjusting NUT Back RailSee Figures 74 PAN Head Screw To Adjust the RIP Fence IndicatorLubrication MaintenanceAccessories General MaintenanceProblem Cause TroubleshootingSolution HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No TS3660 Serial No Customer Service Information
Top Page Image Contents