RIDGID TS3660 manual Table of Contents, Introduction

Page 2

TABLE OF CONTENTS

 

Introduction

2

General Safety Rules

3-4

Specific Safety Rules

4-5

Symbols

6-7

Electrical

8-10

Glossary of Terms

11

Features

12-13

Tools Needed

14

Loose Parts

15-16

Assembly

17-28

Operation

29-40

Adjustments

41-47

Maintenance

48

Accessories

48

Troubleshooting

49-50

Warranty

51

Parts Ordering/Service

52

INTRODUCTION

 

This tool has many features for making the use of this product more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate.

2

Image 2
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF Specific Safety Rules Before Making a CUT, be Sure ALL ADJUST- Ments are Secure  Never Operate the SAW on the FloorSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Authorized Service Center for repair. When servicExtension Cords Speed and WiringElectrical Electrical ConnectionChanging Motor Voltage See Figures 2See Figure Junction BOX Manual Reset ButtonMotor Thermal Overload Protector Glossary of Terms RIP Fence FeaturesProduct Specifications Bevel ScaleKnow Your Table SAW OverviewSquare Framing Square Tools NeededHEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16 Loose Parts Key Description QtyLoose Parts List Mounting Holes AssemblyUnpacking To Assemble LEG Stand and Storage Brackets Screw With Washer To Install Extension TablesTo Mount the Table SAW to the LEG Stand To Install the HERC-U-LIFT Mobile Base to the LEG Stand Lock Blade Tube Height Lock Knob Adjusting Handwheel To Install Bevel Adjusting HAND- WheelTo Install Height Adjusting HAND- Wheel To assemble the Herc-U-Lift to the leg standTool Storage Square Head Bolt To Store AccessoriesTo Install Front and Back Rails Square Head BoltFront Rail Rear Shims To Adjust Front and Back RailsSee Figures 23 SET Screws RIP Fence in Locked Position Unlocked Position To Install RIP FenceTo Check the Throat Plate See Figures 27To Align Blade Guard Assembly to the Blade To Install Spacer BARTo Install Blade Guard Assembly To Install Belt To Mount Motor AssemblyTo Install the Belt Guard Motor AssemblyTo Secure the Electrical Cords To Install Switch AssemblyTo Install END Caps To Adjust Blade Depth To Adjust Blade AngleOperation Push Sticks Push Blocks HOW to Make a FeatherboardFeatherboard See Figures 41Cross CUT Types of CutsCutting Tips Unlock Pedal Metal Platform To USE the IND-I-CUT FeatureTo USE the HERC-U-LIFT Mobile Base to Move the Table SAW To USE the SAW Dust Chute To USE the MICRO-ADJUST Feature on the RIP FenceMICRO-ADJUST Wheel Dust Chute See Figures 46See Figures 49 Switch KEY Removed Switch onTo Make a Cross CUT To Make a RIP CUT To Make a Miter CUTViewed from the FRONT, below the Table SAW To Make a Bevel Cross CUTTo Make a Bevel RIP CUT To TightenScale RIP Fence To Make a Compound Bevel Miter CUTBevel RIP CUT Blade Angled To Make a Large Panel CUT To Make a NON-THROUGH CUT NON-THROUGH CUTTo Make a Dado CUT Dado CUTTo REMOVE/REPLACE the Throat Plate AdjustmentsTo Install Zero Clearance Throat Plate Removing Throat Plate Zero ClearanceBlade Wrench Washer NUT Framing Square To Replace the SAW BladeSee Figures 62 Trunnion Bolt Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 64 Trunnion Bolt LeverScrews Bevel Lock Lever Blade AT 90˚ Position To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 67 To Adjust the Bevel Adjusting HAND- Wheel To Adjust the Miter GaugeSee Figures 74 To Align and Adjust the RIP FenceLocking Lever HEX Head Screws Adjusting NUT Back Rail To Adjust the RIP Fence Indicator PAN Head ScrewGeneral Maintenance MaintenanceAccessories LubricationTroubleshooting Problem CauseSolution What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No TS3660 Serial No