RIDGID TS3660 manual To Adjust the RIP Fence Indicator, PAN Head Screw

Page 47

ADJUSTMENTS

TO ADJUST THE RIP FENCE INDICATOR

See Figure 77.

The rip fence has two indicators: one for use when the rip fence is on the right side of the saw blade and one for use when the rip fence is on the left side of the saw blade.

NOTE: The blade guard assembly must be removed to perform this adjustment. Reinstall the blade guard assembly when the adjustment is complete.

Unplug the saw.

Place the rip fence on the saw table so that it lightly touches the right side of the saw blade. Lock the rip fence in place.

Loosen pan head screw and adjust the right indicator so that the red line is located over the "zero" line on the right rip scale on the front rail. Retighten screw.

Reposition the rip fence on the saw table so that it lightly touches the left side of the saw blade. Lock the rip fence in place.

Loosen pan head screw and adjust the left indicator so that the red line is located over the "zero" line on the left rip scale on the front rail. Retighten screw.

PAN HEAD

SCREW

Fig. 77

47

Image 47

Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Never Operate the SAW on the Floor Specific Safety Rules Before Making a CUT, be Sure ALL ADJUST- Ments are Secure  Blade Coasts After Being Turned OFFSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsAuthorized Service Center for repair. When servic ServiceElectrical Connection Speed and WiringElectrical Extension CordsSee Figures 2 Changing Motor VoltageSee Figure Junction BOX Manual Reset ButtonMotor Thermal Overload Protector Glossary of Terms Bevel Scale FeaturesProduct Specifications RIP FenceOverview Know Your Table SAWSquare Framing Square Tools NeededHEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16 Key Description Qty Loose PartsLoose Parts List Mounting Holes AssemblyUnpacking To Assemble LEG Stand and Storage Brackets Screw With Washer To Install Extension TablesTo Mount the Table SAW to the LEG Stand To Install the HERC-U-LIFT Mobile Base to the LEG Stand To assemble the Herc-U-Lift to the leg stand To Install Bevel Adjusting HAND- WheelTo Install Height Adjusting HAND- Wheel Lock Blade Tube Height Lock Knob Adjusting HandwheelSquare Head Bolt To Store AccessoriesTo Install Front and Back Rails Tool Storage Square Head BoltFront Rail Rear Shims To Adjust Front and Back RailsSee Figures 23 See Figures 27 To Install RIP FenceTo Check the Throat Plate SET Screws RIP Fence in Locked Position Unlocked PositionTo Align Blade Guard Assembly to the Blade To Install Spacer BARTo Install Blade Guard Assembly Motor Assembly To Mount Motor AssemblyTo Install the Belt Guard To Install BeltTo Secure the Electrical Cords To Install Switch AssemblyTo Install END Caps To Adjust Blade Angle To Adjust Blade DepthOperation See Figures 41 HOW to Make a FeatherboardFeatherboard Push Sticks Push BlocksCross CUT Types of CutsCutting Tips Unlock Pedal Metal Platform To USE the IND-I-CUT FeatureTo USE the HERC-U-LIFT Mobile Base to Move the Table SAW See Figures 46 To USE the MICRO-ADJUST Feature on the RIP FenceMICRO-ADJUST Wheel Dust Chute To USE the SAW Dust ChuteSee Figures 49 Switch KEY Removed Switch onTo Make a Cross CUT To Make a Miter CUT To Make a RIP CUTTo Tighten To Make a Bevel Cross CUTTo Make a Bevel RIP CUT Viewed from the FRONT, below the Table SAWScale RIP Fence To Make a Compound Bevel Miter CUTBevel RIP CUT Blade Angled To Make a Large Panel CUT NON-THROUGH CUT To Make a NON-THROUGH CUTDado CUT To Make a Dado CUTRemoving Throat Plate Zero Clearance AdjustmentsTo Install Zero Clearance Throat Plate To REMOVE/REPLACE the Throat PlateBlade Wrench Washer NUT Framing Square To Replace the SAW BladeSee Figures 62 Trunnion Bolt Lever Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 64 Trunnion BoltScrews Bevel Lock Lever Blade AT 90˚ Position To SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚See Figures 67 To Adjust the Miter Gauge To Adjust the Bevel Adjusting HAND- WheelSee Figures 74 To Align and Adjust the RIP FenceLocking Lever HEX Head Screws Adjusting NUT Back Rail PAN Head Screw To Adjust the RIP Fence IndicatorLubrication MaintenanceAccessories General MaintenanceProblem Cause TroubleshootingSolution HOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No TS3660 Serial No Customer Service Information