RIDGID TS3660 manual To Assemble LEG Stand and Storage Brackets

Page 18

ASSEMBLY

TO ASSEMBLE LEG STAND AND STORAGE BRACKETS

See Figures 10 - 11.

Separate the following: side brace (2), front brace (1), back brace (1), legs (4), miter gauge storage hook (1), rip fence storage hooks (2), foot braces (4), and leveling feet (4).

Locate the following parts:

8 hex nuts (3/8-16)

15 carriage bolts (5/16-18 x 5/8 in.)

15 hex nuts, flanged (5/16-18)

 Place front brace inside first leg piece. Align holes on the

LEG

HEX NUT,

FLANGED (5/16-18)

BACK
BRACE	FRONT
	FRONT
	BRACE

front brace with the holes on the leg piece. Insert two

carriage bolts and hand tighten using flanged hex nuts.

 Attach a second leg piece to the other side of the front

brace using two carriage bolts and flanged hex nuts.

 Repeat the above steps once for the back brace.

 Place side brace inside leg piece. Align holes on side

brace with the holes on the leg piece.Secure the miter

gauge storage hook to the leg on the right side of the leg

stand. Insert two carriage bolts and hand tighten using

flanged hex nuts.

Place side brace inside leg piece. Align holes on side

SIDE

BRACE

CARRIAGE BOLT (5/16-18 x 5/8 in.)

FOOT

BRACE

LEVELING

FOOT

HEX NUT (3/8-16)

Fig. 10



brace with the holes on the leg piece. Secure the two rip

fence storage hooks to the leg on the left side of the leg

stand. Insert two carriage bolts and hand tighten using

flanged hex nuts.

This completes two of the four sides of the leg stand.

Thread one hex nut (3/8-16) on the screw on the leveling foot and turn until it stops.

Slip a foot brace onto the leveling foot before placing the leveling foot in the hole in the bottom of the leg. Secure with another hex nut.

Insert a screw through the hole in the leg stand.

Adjust the feet all the way to the bottom of the leg. Using a wrench, securely tighten all hex nuts.

SIDE

BRACE

MITER GAUGE

STORAGE

HOOK

		FRONT
	RIP FENCE	BRACE
	RIP FENCE
	STORAGE	LEG
	HOOKS	LEG
	HOOKS
		LEG STAND ASSEMBLED

Fig. 11

18

Image 18

Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF Specific Safety Rules Before Making a CUT, be Sure ALL ADJUST- Ments are Secure  Never Operate the SAW on the FloorSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Authorized Service Center for repair. When servicExtension Cords Speed and WiringElectrical Electrical ConnectionChanging Motor Voltage See Figures 2Junction BOX Manual Reset Button Motor Thermal Overload ProtectorSee Figure Glossary of Terms RIP Fence FeaturesProduct Specifications Bevel ScaleKnow Your Table SAW OverviewTools Needed HEX Keys 4 2.5 mm, 1/8 in., 5/32 in., 3/16Square Framing Square Loose Parts Key Description QtyLoose Parts List Assembly UnpackingMounting Holes To Assemble LEG Stand and Storage Brackets To Install Extension Tables To Mount the Table SAW to the LEG StandScrew With Washer To Install the HERC-U-LIFT Mobile Base to the LEG Stand Lock Blade Tube Height Lock Knob Adjusting Handwheel To Install Bevel Adjusting HAND- WheelTo Install Height Adjusting HAND- Wheel To assemble the Herc-U-Lift to the leg standTool Storage Square Head Bolt To Store AccessoriesTo Install Front and Back Rails Square Head BoltTo Adjust Front and Back Rails See Figures 23Front Rail Rear Shims SET Screws RIP Fence in Locked Position Unlocked Position To Install RIP FenceTo Check the Throat Plate See Figures 27To Install Spacer BAR To Install Blade Guard AssemblyTo Align Blade Guard Assembly to the Blade To Install Belt To Mount Motor AssemblyTo Install the Belt Guard Motor AssemblyTo Install Switch Assembly To Install END CapsTo Secure the Electrical Cords To Adjust Blade Depth To Adjust Blade AngleOperation Push Sticks Push Blocks HOW to Make a FeatherboardFeatherboard See Figures 41Types of Cuts Cutting TipsCross CUT To USE the IND-I-CUT Feature To USE the HERC-U-LIFT Mobile Base to Move the Table SAWUnlock Pedal Metal Platform To USE the SAW Dust Chute To USE the MICRO-ADJUST Feature on the RIP FenceMICRO-ADJUST Wheel Dust Chute See Figures 46Switch KEY Removed Switch on To Make a Cross CUTSee Figures 49 To Make a RIP CUT To Make a Miter CUTViewed from the FRONT, below the Table SAW To Make a Bevel Cross CUTTo Make a Bevel RIP CUT To TightenTo Make a Compound Bevel Miter CUT Bevel RIP CUT Blade AngledScale RIP Fence To Make a Large Panel CUT To Make a NON-THROUGH CUT NON-THROUGH CUTTo Make a Dado CUT Dado CUTTo REMOVE/REPLACE the Throat Plate AdjustmentsTo Install Zero Clearance Throat Plate Removing Throat Plate Zero ClearanceTo Replace the SAW Blade See Figures 62Blade Wrench Washer NUT Framing Square Trunnion Bolt Heeling Paralleling the Blade to the Miter Gauge GrooveSee Figures 64 Trunnion Bolt LeverTo SET the Bevel Indicator and Bevel Stops AT 0˚ and 45˚ See Figures 67Screws Bevel Lock Lever Blade AT 90˚ Position To Adjust the Bevel Adjusting HAND- Wheel To Adjust the Miter GaugeTo Align and Adjust the RIP Fence Locking Lever HEX Head Screws Adjusting NUT Back RailSee Figures 74 To Adjust the RIP Fence Indicator PAN Head ScrewGeneral Maintenance MaintenanceAccessories LubricationTroubleshooting Problem CauseSolution What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No TS3660 Serial No